一、模具词汇：会议情况报告
1.模具：mold; mould; tool
2.模胚：mold ba
3.塑胶，胶位：plastic
4.模具图纸：mold drawing
5.模胚何可人/模架：mold ba; mold frame
6.模板：mold plate
7.模具类型：mold type(两板模：2-plate mold, 三板模：3-plate mold)
8.前模（母模）：cavity, fixing side(固定侧)；cavity也有型腔的意思，缩写为cav.
9.后模：core; moving side(移动侧)
10.镶件（入子）：inrt;
可换镶件：interchangeable inrt
前（后）模镶件：cavity(core) inrt
11.进胶点，浇口：injection point,; gate
入水形式：gate type
潜水：sub-gate;tunnel-gate
直入水（大水口）：direct gate
边入水：edge gate
点入水：pin point gate
扇形入水：fan gate
香蕉形入水：banana gate
腰果形入水：cashew gate
月亮形入水：moon gate
1.面板：top clamp plate
2.底板：bottom clamp plate
国际象棋英语
3.水口板：runner stripper plate
4.推板：stripper plate
5.托板：support plate
6.方铁(也有公司叫模脚)：spacer block
7.顶针面板：ejector retainer plate
8.顶针底板：ejector plate
9.导柱：leader pin
10.导套：leader bush
1.中托司：ejector guide pin
2.中托司套：ejector guide bush
3.排气：vent
4.回针：return pin
5.斜边，斜导柱：angular pin
电梯培训
6.撑头：support pillar
7.定位圈：locating ring
8.销钉：dowel pin
9.隔水片：baffle
10.唧嘴：sprue bushing
1.变形：deform
deformed
deformation
warp
warped
warpage
distort
distorted
distortion
2.缩水：shrink
缩水率：shrinkage rate
缩水纹：sink mark
酒瓶盆景3.顶白：ejection mark
4.流痕：flow mark
5.粘模：sticking
6.拖花：scratch
7.批锋：flash
8.烧焦痕：burn mark
9.困气：gas trap
10.走胶不满：short shot; not filled
11.流道类型：runner type
冷流道：cold runner
热流道：hot runner
一、句子表达：
1.
这个产品有点变形
This part is a little deformed.
2.
产品骨位太厚，表面容易产生缩水
This rib is too thick, easy to have(cau/appear) sink mark.
3.
周良洛成形后，产品表面有困气，建议增加镶件。
After molding, there is gas trap on the part surface,suggest adding inrt.
4.
产品表面会有缩水纹
There will be sink mark on part surface.
5.
产品粘后模
The part is sticking on the core.
1.现在图纸上为前后模原身出，我们希望做镶件，可以吗？
On the drawing,the cavity and core is directly cut into plate(mold ba),we want to make inrt,OK？
2.请确认产品排位是否OK。
Plea confirm the layout of the part is OK or not.
3.为方便加工（为增加骨位排气），建议此处做镶件。才十二一
For easy machining,(For adding vent at rib),we suggest making inrt here.
为了做某事、、、
----In order to do、、、
1.为了满足啤机(注塑机)的吨位，将面板宽度修改为35mm,可以吗？
In order to meet the injection machine ton,we want to change the width of the top clamp plate to 35mm,OK？
2.导柱需加油槽及拆卸牙。
Grea slot and the screw must be added to the leader pin.
3.顶针与运水距离较近，可以将顶针改小吗？
EJ pin is too clo to the cooling, could we change a smaller EJ pin?
1.你好，很高兴见到你。
Hello.Nice to meet you.
扫除天下2.我是工程师（设计师），我叫、、、
I am an engineer(designer),my name is---
3.我们可以改做三板模吗？
Could we change it to 3 plate mold?
4.在此处做潜水，可以吗？
Could we make a sub gate here?
5.我们建议使用热流道
We suggest using hot runner.
sub-flush在这里应该是个形容词，差不多是指刚好低于一个面。flush指与之齐平的，sub-flush则是稍稍嵌进去的。
