HEP SERIES ELECTRIC CATERPILLAR PIZZAR
OVEN
OPERATION MANUAL
During transportation, the machine should be taken care for the strong vibration. The package cannot be put upside sown. It should be put inside the non corrosive gas warehou. If it is put in the open air, it should be covered with water-proof cloth.
3. Installation:
(1)The machine should be put on the flat place. And it should have more than 10cm space with around un-inflammables. In the front, it should have enough working space.
(2)You should have fixed power wiring near the working sit and the wires should be equipped with switch break down and electric leaking It must not have any substance put around the switch.
(3)The power supply should be the same as the indication on the nameplate of the machine. The power supply difference should not be over 10% of the rated voltage.
个体
(4)The earth wire of the machine (yellow & green one) is together with the power wire. It should be fixed to the qualified earth wire for safety.
(5)The wire terminals are in the back of the machine. You should connect with over 2.5mm 2 cross s
ectional area copper wires.
(6)If the power wire is damaged, you should call your supplier or agent to replace it for you.
好喝的啤酒(7)The installation should be done by the qualified electricians.
(8)This equipment is not equipped to be ud by unwell, unresponsive or mentally disturbed people, including children, unless under the guidance or help of persons who are responsible
for their curity. Keep an eye on children and keep them away from playing around the equipment.
WARNNING: WHEN THE MACHINE IS WORKING, THE TEMPERATURE IS HIGH, NEVER TOUCH IT AND KEEP CHILDREN AWAY FROM THE MACHINE.
4. Operation:
萧翎
(1) The machine outlook is as following:
挽回感情的句子1. Control switch: for controlling the operation of the machine
和其他人一样2. Up temperature control switch: for adjusting the heating temperature
3. Fan switch: for turning on the fan to lower the temperature
4. Down temperature control switch: for adjusting the heating temperature
5. Running switch: for controlling the running of caterpillar. It can go forward or backward.
6. Speed regulator: for regulating the speed of caterpillar running
7. Adjusting bolt: for adjusting the height of access plate
8. Tray: for containing the baked food
9. Caterpillar adjusting bolt: for adjusting the caterpillar fixed or lood
10. Power lamp: indicate the power is on or off
(2). the caterpillar is adjusted well in the factory. After operation for some time, if you like to adjust it, you can loo the caterpillar adjusting bolt “ 9” to adjust it.
(3). Turning out of the both trays”8” . After operation, fold it to cover the caterpillar.
(4.) According the thickness of the food, adjust the adjusting bolt “7” to make the gab between plate and caterpillar suitable for the food going through. After adjustment, fix the bold again. (5). When everything is ready, turn on the power, the power lamp”10” is on, press the control switch “1’, the control switch lamp is on , turn the temperature control switch “2”, and “4”clockwi to the required temperature. Then the heaters begin working. When the temperature increas to the required ttin
无法逃脱g, the thermostat will cut off the power automatically and the heaters stop working. When the temperature decrea, the thermostat will turn on the power automatically, the heater works again. In this circulation, the temperature is kept in the tting range.
NOTICE：To avoid dangers caud by accidentally wrong restoration of the thermal circuit breaker, don’t supply power to the equipment with an exterior device of switches, like timers, nor connect it to a circuit which is connected or cut off regularly by universal parts.
(6) The adjustment range of the temperature is 50-300c. (Suggesting the baking temperature is 250-300c). The up and down temperature are controlled parately. You can t the baking temperature according to the baking requirements of the foods
(7) During bakery, when the oven reaches the tting temperature, it should take 5 minutes more to pre-heating before operation.
(8) Turn the running switch “5” to forward position and turn on the speed regulator “6” and turn the regulator to the required speed., the caterpillar begins running . Then you can put pizzas or other foods on to the inlet caterpillar and they will be conveyed to the oven for bakery and will go out from the exit. When the food cannot reach the requirement, you can turn on the running switch again for t
he cond time bakery.
(9) The machine is equipped with over heating protection device. If the thermostat do not works, the oven temperature increas without stop, when it is higher than the machine limited tting, the device will cut off the power automatically. If you like to turn on the machine, you have to press the ret switch in the back of the machine to recovery. If you cannot press down the ret switch, that means the machine still in high temperature. You should do it again after the machine is cold down
(10) After operation, plea turn all of the switches to zero and cut off the power.
如何选择职业(11) Before bakery, turn on the fan switch “3” otherwi the electric component will be burnt out due to the oven temperature is too high.
WARNING: NEVER PUT ANY IMFLAMMABLES ON THE MACHINE!!
5．Electric Diagram
L
N E
HEP-12 ELECTRIC DIAGRAM
肠炎宁片说明书
