AEROSPACE STANDARD
(R) Aerospace First Article Inspection Requirement
® AS9102
Technically equivalent to AECMA prEN 9102
REV. A
FOREWORD
In December 1998, the Aerospace Industry had established the International Aerospace QualityGroup (IAQG) with the purpo of achieving significant improvements in quality and reductionsin cost throughout the value stream.
This organization, with reprentation from Aerospace companies in Americas, Asia and Eu
ropeand sponsored by SAE, SJAC, and AECMA has agreed to take responsibility for the technical contents of this standard.
TABLE OF CONTENTS
1. ……….............. ..3
1.…………....................…….................… 3
1.……..............….... 3
仓库文员1.…..... 3
2. …....... 3
3. DEFINITIONS ..........................................................……..... 4
4. …......... 5
5. REQUIREMENTS ......................................................…........5
5.1 Part Requirements .....................................................…........5
5.2 Evaluation Activities .....................................................….....6
5.3 Partial or Re-accomplishment of First Article Inspection….. 6
5.4 .7
祭母文大全5.7
5.5. 7
怀孕性欲5.5.2 Characteristic Accountability ..............................................8
5.5.3 Record 8
5.6 Control of Records ................................................................ 8
6. . 9
APPENDIX A FORMS AND GUIDELINES TO COMPLETE THE FORMS ..10
1. INTRODUCTION:
1.1 Scope:
This SAE Aerospace Standard (AS) establishes requirements for performing anddocumenting the First Article Inspection (FAI).
1.2 Purpo:
The purpo of the First Article Inspection is to give objective evidence that allengineering, design and specification requirements are correctly understood, accounted for, verified, and recorded. The purpo of this standard is to provide a consistent documentation requirement for aerospace components FAI.
1.3 Convention:
The following convention is ud in this Standard.什锦火锅
蝴蝶发饰• The words .shall. and .must. indicate mandatory requirements.
• 贾联亭The word .should. indicates mandatory requirements with some flexibility allowed incompliance methodology. An Organization is permitted to show that its approach meets the intent of the requirement and this standard.
航空标准
航空首件检查要求
版本：A
前言
1998年12月，航空工业成立的国际航空质量部门（IAQG），目的是为了提高质量和降低成本。
本组织，由来自美国、亚洲、欧洲航空公司的代表，由SAE、AJAC、AECMA赞助，同意本标准中的技术内容
内容目录（略）
1.简介
1.1 范围
本SAE 航空标准（AS）是对首次加工产 品检查执行和文件要求。
1.2 目的
首次产品检查的目的是为了确认所有的工程、设计、规格要求被正确的理解、计算、检验和记录。本标准的目的是提供一个一致的航空元器件FAI文件。
1.3 规定
本标准中有以下的规定：
“shall”和“must”表示强制执行
“shoud”指有弹性的强制执行
• Words .typical., .example. or .e.g.. show suggestions given for guidance only.
• .Notes. are ud for additional clarification.
2. REFERENCES:
1. International Aerospace Standard 9100 .Quality Systems - Aerospace - Model forQuality Assurance in Design, Development, Production, Installation and Servicing..
2. International Aerospace Standard 9103 .Variation Management in Key Characteristics..
3. International Aerospace Standard 9131 .Quality Systems – Nonconformance Documentation..
3. DEFINITIONS:
ATTRIBUTE DATA: A result from a characteristic or property that is appraid only as towhether it does or does not conform to a given requirement (for example, go/no-go,accept/reject, pass/fail, etc.).
DELIVERABLE SOFTWARE: Embedded or loadable airborne, space borne or ground su
坐南向北pport software components that are part of an aircraft Type Design, weapon system,missile or spacecraft.
DESIGN CHARACTERISTICS: Tho dimensional, visual, functional, mechanical, and material features or properties, which describe and constitute the design of the article as specified by Drawing Requirements. The characteristics can be measured, inspected,tested, or verified to determine conformance to the design requirements. Dimensional features include in-process locating features such as target-machined (or forged/cast) dimensions on forgings and castings, and, weld/braze joint preparation necessary for acceptance of finished joint. Material features or properties may include processing variables and quences, which are specified by the drawing (e.g., heat treat temperature,fluorescent penetrant class, ultrasonic scans, quence of welding and heat treat). The provide assurance of intended characteristics that could not be otherwi defined.描写眼神的句子
