模具专业英语 (模具设计)
鲁大师温度
模具专业英语
感谢论坛发贴网友,pinery
模具述语
一、入水:gate 撑头: support pillar 进入位: gate location 唧嘴: sprue bushing 水口形式:gate type 挡板:stop plate 大水口:edge gate 定位
圈:locating ring 细水口: pin-point gate 锁扣:latch 水口大小:gate size 扣鸡:parting lock t 转水口: switching runner/gate 推杆:push bar 唧嘴口径: sprue diameter 栓打螺丝:S.H.S.B 二、流道: runner 顶板:eracuretun 热流道: hot runner,hot manifold 活动臂:lever arm 热嘴冷流道: hot sprue/cold runner 分流锥:spure sperader 唧嘴直流: direct sprue gate 水口司:bush 圆
福兮
形流道:round(full/half runner 垃圾钉:stop pin 流道电脑分析:mold flow analysis 隔片:buffle 流道平衡:runner balance 弹弓柱:spring rod 热嘴: hot sprue 弹弓:die spring 热流道板:hot manifold 中托司:ejector guide bush 发热管:cartridge heater 中托边:ejector guide pin 探针: thermocouples 镶
针:pin 插头: connector plug 销子:dowel pin 插座: connector socket 波子弹弓:ball catch 密封/封料: al 喉塞: pipe plug 三、运水:water line 锁模块:lock plate 喉塞:line lpug 斜顶:angle from pin 喉管:tube 斜顶杆:angle ejector rod 塑胶管:plastic tube 尼龙拉勾:parting locks 快速接头:jiffy quick connector plug/socker 活动臂:lever arm 四、模具零件: mold components 复位键、提前回杆:early return bar 三板模:3-plate mold 气
苦苦挽留阀:valves 二板模:2-plate mold 斜导边:angle pin 边钉/导边:leader
pin/guide pin 术语:terms 边司/导套:bushing/guide bushing 承压平面平
钢铁侠英文
衡:parting surface support balance蓝莓花青素
中托司:shoulder guide bushing 模排气:parting line venting 中托边
鞠躬精粹L:guide pin 回针碰料位:return pin and cavity interference 顶针板:ejector retainner plate 模总高超出啤机规格:mold ba shut hight 托板: support plate 顶针碰运水:water line interferes withejector pin 螺丝: screw 料位出上/下模:part from cavith (core) side 管钉:dowel pin 模胚原身出料
位:cavity direct cut on A-plate,core 开模槽:ply bar scot direct cut on
B-plate.
内模管位:core/cavity inter-lock 不准用镶件: Do not u (core/cavity) inrt 顶针: ejector pin 用铍铜做镶件: u beryllium copper inrt 司筒:ejector sleeve 初步：正式：模图设计:preliinary (final) mold design 司筒针:ejector pin 反呵:rever core
反馈的近义词推板:stripper plate 弹弓压缩量:spring compresd length 缩呵:movable core,return core core puller 稳定性好:good stability,stable 扣机：尼龙拉勾::nylon latch lock 强度不够:insufficient rigidity 斜顶:lifter 均匀冷却:even cooling
模胚：架:: mold ba 扣模:sticking
上内模:cavity inrt 热膨胀:thero expansion
下内模:core inrt 公差:tolorance
磨骨后遗症行位：滑块:: slide 铜公(电极::copper electrode 镶件:inrt
压座/斜鸡:wedge
耐磨板/油板:wedge wear plate
压条:plate
