中文 = 英文
顶针 = E.P.
有托顶针 = Stepped E.P.四级英语阅读
扁顶针 = Rectangular E.P.
司筒/司筒针 = E.P.Sleeve
直身导边 = Straight Leader Pin
有托导边 = Shoulder Leader Pin
直身杯司 = Straight Bushing
有托杯司 = Shoulder Bushing
方定位块 = Position Block Set
定位锥 = Taper Pin Set
尼龙塞 = Parting Lock
中托司套 = Ejector Lead Bushing
中托导柱 = Ejector Leader Pin
脱水口螺丝组 = Puller Bolt Set
限位螺丝 = Stopper Bolt
限位钉 = Positioning Pin
管位块 = Slotter Key
弹簧 = Spring
螺钉 = Screw
限位块 = Distance Spacer
无头螺钉 = Screw Plug
平头螺钉 = Socket Head Cap Screw
波子螺丝 = Ball Plunger
定位螺钉 = Positioning Screw Plug
胶圈 = O ring
喉塞 = Taper Screw Plug
法兰 = Locating Ring
唧嘴 = Sprue Bushing
截流塞 = Cooling Circuit Plug
上固定板 = Top Clamping Plate
脱料板 = Runner Stripper Plate
上模板 = Cavity Plate
宁远九嶷山
推板 = Stripper Plate
下模板 = Core Plate
支承板 = Support Plate
间隔板 = Spacer Block
顶针板1 = Ejector Plate 1
顶针板2 = Ejector Plate 2
下固定板 = Bottom Clamping Plate
回针 = Return Pin
拉杆 = Support Pin
拉杆定位介子 = Support Pin Spacer
入党积极分子演讲稿
齿轮 = Gear
丝杆 = Screw
轴承 = Bearing
油缸 = Oil Cylinder
气缸 = Air Cylinder
间隔圈 = Spacer Ring祝福生日
垃圾钉 = Slopper Ring
撑头 = Support Pillar
行位开关组 = Detection Switch Set
站脚 = Distance Spacer
斜顶 = ANGULAR
扣机(尼龙拉勾) = nylon latch lock
模胚(架) = mold ba
上模 = Cavity
上模镶件 = Cavity Inrt张士明
上模镶针 = Inlay Cavity Pin
潜水镶套 = Pin Point Gate Bushing
流道衬板 = Runner Plate
水口扣针 = Runer Lock Pin
行位 = Slider
行位开关组 = Detection Switch Set
站脚 = Distance Spacer
行位导向键 = Slider Certer Rail
行位镶件 = Slider Inrt
斜边 = Angular Pin
方斜边 = Angular Cam
铲鸡 = Locking Block
行位压板 = Slider Guide Rail
隔热板 = Insulation Sheet
压板(其他类) = Holding Plate
楔块 = Spacer Wedge
销钉 = Dowel Pin
下模 = Core
下模镶件 = Core Inrt
支承板 = Support Plate
间隔板 = Spacer Block
下模镶针 = Core Pin
撑头 = Support Pillar
流道衬板 = Runner Plate
水口扣针 = Runer Lock Pin
拉板 = Tension Link
拉板介子 = Tension Link Retainer
行位垫块 = Slide Plate
斜边压块 = Holding Plate For A.P.
斜顶滑座 = Slide Unit For Loo Core
冷胶套 = Sprue Lock Bushing
六道斑图片运水镶件 = Inrt For Cooling
等高螺丝 = Stopper Bolt
入水 = gate
进入位 = gate location
水口形式 = gate type
大水口 = edge gate
细水口 = pin-point gate
水口大小 = gate size
转水口 = switching runner/gate
唧嘴口直径 = sprue diameter
流道 = runner
热流道 = hot runner/hot
manifold
热嘴冷流道 = hot sprue/cold runner
唧嘴直流 = direct sprue gate
圆形流道 = round/full/half runner
流道电脑分析 = mold flow analysis
流道平衡 = runner balance
热嘴 = hot sprue
热流道板 = hot manifold
发热管 = cartridge heater
探针 = thermocouples
插头 = connector plug
插座 = connector socket
密封/封料 = al
运水 = water line/line lpug
喉管 = tube
塑胶管 = plastic tube
快速接头 = jiffy quick connector plug/socker
世界最大的城市
模具零件 = mold components
三板模 = 3-plate mold
二板模 = 2-plate mold
边钉/导边 = leader pin/guide pin
边司/导套 = bushing/guide bushing
中托司 = shoulder guide bushing
中托边 = guide pin
中托导柱 = Ejector Leader Pin
项目工程师脱水口螺丝组 = Puller Bolt Set
限位螺丝 = Stopper Bolt
顶针板 = ejector retainner plate
限位钉 = Positioning Pin
托板 = support plate
螺丝 = screw
管钉 = dowel pin
开模槽 = ply bar scot
内模管位 = core/cavity inter-lock
压座/斜鸡 = wedge
耐磨板/油板 = wedge wear plate
压条 = plate
定位圈 = locating ring
琐扣 = latch
扣鸡 = parting lock t
推杆 = push bar
栓打螺丝 = S.H.S.B
顶板 = eracuretun
活动臂 = lever arm
分流锥 = spure sperader
水口司 = bush
隔片 = buffle
弹弓柱 = spring rod
弹弓 = die spring
镶针 = pin
销子 = dowel pin
波子弹弓 = ball catch
复位键\提前回杆 = early return bar
气阀 = valves
斜导边 = angle pin
术语 = terms
承压平面平衡 = parting surface support balance
模排气 = parting line venting
回针碰料位 = return pin and cavity interference
模总高超出啤机规格 = mold ba shut hight
顶针碰运水 = water line interferes withejector pin
料位出上/下模 = part from cavith (core) side
模胚原身出料位 = cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件 = Do not u (core/cavity) inrt
用铍铜做镶件 = u beryllium copper inrt
初步(正式)模图设计 = preliinary (final) mold design
弹弓压缩量 = spring compresd length
稳定性好 = good stability,stable
强度不够 = insufficient rigidity
均匀冷却 = even cooling
扣模 = sticking
热膨胀 = thero expansion
公差 = tolorance
铜公(电极) = copper electrode
