锻造术语中英文对照
锻压 forging and stamping
金属塑性加工 metal plastic working
金属压力加工 mechanical metal working
体积成形 bulk forming
锻造 forging / hot forging
锻造技术 forging technology / forging technique
锻造工艺 forging technology / forging process
锻工 forger / blacksmith / hammer man / hammer smith / hammerer
塑性 plasticity
坚持一切从实际出发超塑性 superplasticity
可锻性 forgeability
切削性能 machinability
最小阻力定律 the law of minimum resistance
体积不变条件 constance(y) of volume / incompressibility银黄含化滴丸
锻造流线 grain flow / forging flow line
滑移线 sliding line / slip-line
模锻 die forging / clod-die forging / impression die forging
开式模锻 clod-die forging / impression die forging
闭式模锻 no-flash die forging / flashless die forging
锤模锻 clod-die forging / impression die forging / drop forging / stamping
锻压机模锻 mechanical press forging
平锻 uptting / heading
无飞边模锻 no-flash forging
无拔模斜度模锻 no-draft forging
模锻件 forging / workpiece
锻件重量 forging weight
普通锻件 conventional forging
精确（公差）锻件 clo-tolerance forging
锻造工序卡 forging process chart
工序 operation / process / procedure
工步 process step
打击 blow / strike
锻件图 forging drawing
加工余量 machining allowance
镦锻、顶锻 uptting / heading
镦粗 uptting
九牛二虎之力压扁 flattening
去氧化皮 scale-breaking
拔长工步 drawing / elongating / fullering
拔夹钳头 tong-hold drawn / tagging
滚压工步 edging / edge rolling / gathering
弯曲工步 bending
制坯工步 pre-forming
平锻聚料 gathering / pushing up / uptting
锥形镦粗 taper uptting / coning
粗（初）锻 blocker-type forging
预锻 pre-forging / blocking
终锻 finish-forging
返回锻模校正 re-striking
分模线 parting line
模锻斜度、拔模角、拔模斜度 draft angle
外拔模角 outside draft
内拔模角 inside draft
自然拔模角 natural draft
相配拔模角 matching draft
外圆角 corner
内圆角 fillet
未注明圆角 all radii not specified
尺寸按交点注 all dimensions specified form interctions
模锻方案 forging form
一料多件 multi-forging on one billet (bar)
一模两件 two at a time
一模多件 multi at a time
调头锻 turn-end forging
一火多件 multi-forging in one heat
打零件号、炉号码及模具号处 rai part No. heat code and die No. here
除注明处外 unless otherwi noted
贾立群冲孔、切边、校正
冲连皮 punching the wad / punching the slug
冲孔 pierce
盲孔 non-penetrated hole / blind hole
ppt如何转换成word文档连皮 wad / recess / slug
切边 clipping / trimming
飞边 flash
残余飞边、残余飞刺 flash extension / residual flash
切边线、飞边线 flash line / trim line
整形 forming to size
校平 flattening / planishing
校直 straightening
精压、压印 coining / sizing
校正 sizing / tting
冷校正 cold sizing / cold tting
锻造公差、锻造缺陷及检查
锻造公差 forging tolerance / tolerance for impression die forging
确定公差的因素 information required in determining tolerance
锻件形状复杂系数 shape complexity factor of forging
最美逆行者
材质系数 difficulty of material
分模线形状 shape of die line
公差等级 tolerance grad
锻件公称尺寸 nominal dimension of forging
厚度公差 thickness tolerance
模具闭合公差 die closure tolerance
长度、宽度、高度公差 length 、width and height tolerance
模具磨损公差 die wear tolerance
错差、错差公差 mismatch / match tolerance
纷纷暮雪中心距公差 tolerance for centre to centre dimensions
平面度公差 platness tolerance
直线度公差 straightness tolerance
残余飞边及切入深度公差 residual flash and trimmed flat tolerance
顶杆压痕公差 ejector mark tolerance
表面缺陷公差 surface tolerance
壁厚差 difference in wall thickness
冲孔公差 pierced hole tolerance
同轴度公差 axiality tolerance
折叠、折纹 lap / overlap / fold
缺肉、未充满 under-fill
模锻不足 under-pressing
表面缺陷 surface imperfection
氧化皮坑 scale pit
变形 distortion / deformation
毛刺、飞刺 burr / fin
凹陷 void
出气孔金属柱 vent plug
偏心 eccentricity
中间检查 intermediate inspection
流动检查 patrol inspection
外观检查 visual inspection
最后检查 final inspection武八段锦
抽检 random inspection
