变压器用波纹储油柜Corrugate Conrvator for Transformer
产品使用说明书
Product Instruction Manual
沈阳天工热电设备有限公司
Shenyang Tiangong Thermoelectric Equipment Co.,Ltd.
目录
Contents
一、工作原理 (02)
Principle of operation
二、主要性能参数 (03)
Main Performance Parameters
三、产品到货验收 (03)
Check upon delivery
四、产品型号及选用方法 (03)
Product model and lecting method
五、储油柜安装和注油 (04)
五心
Installation&oil injection of conrvator
六、附注及参数表 (07)
Annotation and Parameter List
重要提示Important Tips
■储油柜运输前必须充气压将波纹补偿器压合，防止振动损伤！（方法见附注1）■没有充压的波纹储油柜不能运输！
■到现场未处于充压状态的波纹储油柜不能安装！
●Corrugate pipe must be presd with gas charging before delivering oil
conrvator to prevent damages due to vibration!（See Annotation1）
远东1866●Corrugate conrvator without gas pressing cannot be delivered!
●Corrugate conrvator without gas pressing cannot be installed at site!
变压器用波纹储油柜是新一代全密封型储油柜，是胶囊式和隔膜式储油柜的更新换代产品，具有密封性好、使用寿命长、免维护、安装方便等特点，适用于各类油浸式变压器、电抗器和电容器等电力设备。
Corrugate oil conrvator for transformer is a kind of new-generation full-aling type conrvator,which is the substitutive product of capsule type and diaphragm conrvator.Such oil conrvator is characterized with good aling performance,long-life,no maintenance and convenient installation,etc.,and thus it is suitable to apply for power equipment such as all types of oil immerd transformer,reactor and capacitor,etc.
一、工作原理Principle of operation
BG外油式波纹储油柜采用先进的超柔性不锈钢波纹补偿器作为容积补偿元件和隔离密封元件，在彻底隔绝空气及湿气的条件下，实现对变压器绝缘油的体积补偿。如图1所示，波纹补偿器是一个内腔与大气相通的气囊，放置于绝缘油中，储油腔通过下部连接口与变压器油箱相通。波纹补偿器内腔通过呼吸口与外界大气相通。当绝缘油随温度变化产生体积膨胀或收缩时，促使波纹补偿器伸缩，从而改变柜内油腔大小，实现对绝缘油的体积变化补偿。储油柜各部件的名称及作用参见图1所示。
BG external oil type corrugate conrvator adopts with advanced super-flexible stainless steel corrugate pipe as capacity compensation element and isolation al element,and volume compensation for insulating oil of transformer is realized under complete insulation of air and moisture conditions.As shown in figure1, corrugate pipe is an air bag connecting inner cavity to atmosphere,which is placed in insulation oil.Oil conrvator is connected to oil tank of transformer through bottom connector.Inner cavity of corrugate pipe is connected to outer atmosphere through breath vent.When volume of insulation oil expans or shrinks as the changes of oil temperature,it makes the corrugate pipe extend or shrink,and thus changes the volume of oil chamber in the conrvator,realizing the volume compensation for insulation oil.Designation and function of all parts of oil conrvator refer to figure1.
二、主要性能参数Main Performance Parameters
1.储油柜容积常用范围0.1~12m3（约合20℃油重90~10740kg），适用于变压器总油重不大于120T，
例假能喝茶吗
电压1000KV以下，容量1000MV A以下的各类大中型变压器及其它电力设备。
2.波纹补偿器使用寿命按30年设计，并采用外油式结构，无凝露生成，产品能实现免维护。
3.波纹补偿器耐压能力为±0.1MPa，完全满足全真空注油要求。
4.波纹补偿器工作时对绝缘油产生的最大反力小于0.005MPa，不影响变压器正常保护装置的设定。
记忆辅助●Common volume range of conrvator is from0.1m3to12m3(oil weight about90-10740kg at20℃),
which is suitable for various types of large-medium transformer and other power equipment with total oil weight of transformer not more than120tons,voltage less than1000KV and volume less than1000MV A.
●Life rvice of corrugate pipe is up to30years.
猫咪踩奶是什么意思●Pressure-proof capacity of corrugate pipe is from-0.1MPa to+0.1MPa,with which full-vacuum oil
injection may be realized.
●Max.pressure onto insulation oil is less than0.005MPa when corrugate pipe is working.
三、产品到货验收Check upon delivery
1．检查产品运输途中是否处于充压状态，方法：
a.看油位指示是否如右图所示；
b.打开排气管口时是否有强烈气流喷出。
2．储油柜表面状态检查。检查是否有撞伤、明显变
形等缺陷。
3．主机及附件清点。（见供货单）
4．文件检查。资料袋中应有以下文件：产品说明书、
出厂检验报告、供货单、油位—油温曲线标牌及
合同要求的其它产品资料。
●Check if product is delivered with gas pressing by the
following methods:
a.See whether oil level is indicated as shown in right
figure.
形容气势大的成语
b.Whether there is strong gas flow out when opening
exhaust vent.
●Check the quantity of main machine and accessories.
(See supply list)
●Check surface of conrvator.Check whether there are
any defects such as collision damage and obvious transforms,etc.
●Check documents.Document bag contains the following documents:product instruction manual,ex-works inspection report,supply list,oil level–oil temperature curve plate and other documents required in the contract.
四、产品型号及选用方法Product model and lecting method
●波纹储油柜型号标记如下图：
The model mark for corrugate conrvator is shown in next figure:
五、储油柜安装和注油Installation&oil injection of conrvator
1．配件和工具准备：准备与储油柜连接的阀门、连管、螺栓及胶垫等配件。施工设备及工具：注滤油机、气泵及常用工具如扳手、手锤等。
Preparation for fittings and tool:Prepare the fittings for connecting to oil conrvator such as butterfly valve, connecting tube,bolt and cushion,etc.Tool:air pump,oil injection machine and common tools such as spanner,hand hammer,etc.
2．储油柜安装前准备南昌工学院是几本
①拆除黄色护板→②释放气压→③展开波纹管
Preparation before installing conrvator:
①Dismantle yellow guard plate→②Relea gas pressure→③Unfold corrugate pipe
3.储油柜安装The conrvator i nstallation
●储油柜吊装落位，连接好与变压器相通的管路。
●将注油管和排气管连至变压器下部，并连接密封可靠
的阀门；（见右图）
●将极限油位报警装置控制线路接好，连接方法见本节
条目6；
●安装完毕，准备注油。
●Handle conrvator into position,and connect the pipes
to transformer well.
●Connect oil injection pipe and exhaust pipe to the bottom
of transformer and then connect reliable aling valve.
(e right figure)
哺乳期能吃皮蛋吗
●Connect control circuit of limit oil level alarm device,
refers to clau6.
●Complete installation and prepare for oil injection.
