to reduce the risk of fire, electric shock, or personal injury.
1. Read all instructions carefully.
2. Follow all warnings and instructions marked on the product.
3. Unplug the product from power outlets before cleaning. Do not u
liquid or aerosol cleaners. U a moist cloth for cleaning.
4. Do not u the product near water, for example near a bathtub, wash
bowl, kitchen sink, etc.
5. Place the product curely on a stable surface. Serious damage and/or injury may result if the product falls.取信
6. Do not cover slots and openings on the product. They are provided for
ventilation and protection against overheating. Never place the product near radiators, or in a place where proper ventilation is not provided.
7. U only the power source marked on the product. If you are not sure of
the type of power supplied to your home, consult your dealer or local
power company.
8. Do not overload power outlets and extension cords. This can result in
the risk of fire or electric shock.
9. Never push any objects through slots in the product. This may result
in the risk of fire or electric shock. Never spill any liquid on the product.
10. To reduce the risk of electric shock, do not disasmble the product.
Opening or removing covers may expo you to dangerous voltages or other risks. Incorrect reasmbly can cau electric shock when the
product is subquently ud.
11. Unplug the product from power outlets and take to an authorized
rvice center when the following conditions occur:
A. When the power cord is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been expod to rain or water.
山东樱桃
D. If the product does not work normally by following the operating
instructions. Adjust only controls covered by the operating
instructions. Improper adjustment may require extensive work by an authorized rvice center.
E. If the product has been dropped or physically damaged.
F. If the product exhibits a distinct change in performance.
猪肉脂肪含量12. During thunderstorms, avoid using telephones except cordless types.
There may be a remote risk of an electric shock from lightning.
2 TROUBLESHOOTING GUIDE
15
TABLE OF CONTENTS
Important Safety Instructions (2)
Battery Cautions (3)
About your SEMP FT9007 (5)
Features (6)
Handt Controls & Functions (7)
Ba Unit Controls & Functions (8)
Selecting a Location to Install your Telephone (9)
Installing the B attery Pack (10)
Selecting Tone or Pul Mode (10)
Ringer Volume (11)
Answering an Incoming Call (11)
Using the One Way Page Feature (11)
Using the Scan Button (11)
Making an Outgoing Call (12)党委制
Adjusting the Handt Volume (12)
Using the Flash F unction (12)
Using Last Number Redial (13)
Using the Pau function (13)
Using Auto Answer/Auto Standby (13)
Storing Telephone Numbers to Memory (14)
Dialing Telephone Numbers from M emory (14)
Mute F unction (14)
Troubleshooting guide (15)
4 USING LAST NUMBER REDIAL
To call the last phone number dialed. Press the [TALK] button. Press the [RE/PAUSE] button to redial the last number that you called.
USING THE PAUSE FUNCTION
In some cas, such as long distance dialing rvice, a pau may be needed in the dialing quence when storing or dialing
a telephone number.
1. Press the [RE/PAUSE] button to inrt a 3 cond delay between dialed numbers.
USING THE AUTO ANSWER/AUTO STANDBY FEATURE When the handt is in the ba unit, you can make or answer a call without pressing the [TALK] button by simply removing it from the ba unit
1. Place the handt in the ba unit cradle to hang up the phone.
13
Features
Long Range 900MHz Digital
Handt Volume Control
Compandor Noi reduction
Four Function Keys: PAUSE, FLASH, REDIAL, channel scan Auto Standby
Auto Talk
Mute function
Memory phone number storage
Page Key
Tone/Pul switch able dialing.
10 number speed dial.
Last number redial.
Channel button to lect a clear channel if interference occurs during conversation
Handt locator [PAGE]
Rechargeable NI-MH battery pack
High/Low ringer volume tting as well as ringer off. tting. Easy Installation
6 RINGER VOLUME
There is HIGH and LOW ringer volume tting as well as a ringer off tting.
残忍的反义词
1. Press the [FLASH/PROG] button until the IN USE LED blinks, then press the VOLUME button to your desired volume level. ANSWERING AN INCOMING CALL
If the handt is on the cradle
You can answer the call by simply picking up the handt from the ba unit cradle.
If the handt is out of the cradle
To answer a call when the handt is removed from the ba unit, press the TALK button on the handt.
After completing the conversation
When you finish your conversation, press the handt [TALK] button or place the handt in the ba unit cradle to hang up. USING THE ONE WAY PAGE FEATURE
Press the [PAGE] button on the ba unit, the handt will keep on beeping. Press the [PAGE] button to stop it from beeping. This feature can be ud to locate the handt if you have misplaced it.
11
8
SELECTING A LOCATION TO INSTALL YOUR TELEPHONE Select a location, which meets the following requirements: 1. Near an AC electrical outlet. 2. Near a telephone line jack.
3. Away from any electrical machinery, appliances, and metal walls or filing cabinets.
4. Inrt the plug at the end of the AC power adapter cord into the jack provided on the rear of the ba unit.
中队长竞选稿5. Plug the AC Power adaptor into a wall outlet.
6. Inrt the plug of the telephone line cord into the jack on the ba unit.
7. Inrt the remaining end of the line cord into an existing telephone wall jack.
8. Place the handt in the ba unit cradle; the [IN
英国茶USE/CHARGE] LED will light red indicating the handt battery pack is charging. Let the battery pack charge for 15 hours prior to using your telephone.
9
Installing the Handt Battery Pack
1. Remove the battery cover by pressing the latch and sliding the cover down and off of the Handt.
双卡双待怎么设置2. Place battery pack in the battery compartment.
3. Connect the 2-pin plug from the battery pack into the
battery socket pins inside the battery. Plea obrve the 2-pin plug and socket pins correct orien
tation.
4. Reinstall the battery compartment cover by sliding the
cover up until it latches into the handt. OPERATION
SELECTING TONE OR PULSE DIALING
TONE MODE (Default)
1. First press the [FLASH/PROG] button until the IN USE LED blinks and then press the [*] button.
PULSE MODE
1. First press the [FLASH/PROG] button until the IN USE LED blinks and then press the [#] button.
10 Handt Controls & Functions
7
