模具名词中英文对照表0
序号中文名英文名0
1 一、水口gate0
2 进水位gate location0
3 水口形式gate type0
4 大水口edge gate0
5 细水口pin-point gate0
6 水口大小gate size0
7 转水口switching gate0
8 唧嘴口径sprue diameter0
9 二、流道runner0
10 热流道hot runner0
11 冷流道cold runner0
12 唧嘴直流direct sprue gate0
13 圆形流道round runner0
14 模流分析mold flow analysis0
15 流道平衡runner balance0
16 热嘴hot sprue0
17 热流道板hot manifold0
18 发热管cartridge heater0
19 探针thermocouples0
20 插头connector plug0
21 插座connector socket0
22 密封/封料al0
23 三、运水water line0
24 喉塞line pug0
25 喉管tube0
26 塑胶管plastic tube0
27 快速接头jiffy quick connector plug0
28 四、模具零件mold components0
29 三板模three-plate mold0
模具名词中英文对照表0
序号中文名英文名0
30 二板模two-plate mold0
31 边钉/导边leader pin/guide pin0
32 边司/导套bushing/guide bushing0
33 顶针板ejector retainer plate0
34 托板support plate0
35 螺丝screw0
36 管钉dowel pin0
37 开模槽ply bar score0
38 内模管位core/cavity inter-lock0
39 顶针ejector pin0
40 司筒ejector sleeve0
41 司筒针ejector pin0
42 推板stripper plate0
43 缩呵movable core0
44 扣机（尼龙拉勾）nylon latch lock0
45 斜顶lifter0
46 模胚（架）mold ba0
47 母模cavity inrt0
48 公模core inrt0
49 行位（滑块）slide0
50 镶件inrt0
51 压座/斜鸡wedge0
52 耐磨板/油板wedge wear plate0
53 压条plate0
54 撑头support pillar0
55 唧嘴sprue bushing0
56 挡板stop plate0
57 定位圈locating ring0
58 锁扣latch0
模具名词中英文对照表0
序号中文名英文名0
59 扣鸡parting lock t0
60 推杆push bar0
61 栓打螺丝S.H.S.B0
62 顶板ejector plate0
63 活动臂lever arm0
64 水口司bush0
65 垃圾钉stop pin0
66 隔片buffle0
67 弹弓柱spring rod0
68 弹弓die spring0
69 镶针pin0
70 销子dowel pin0
71 波子弹弓ball catch0
72 喉塞pipe plug0
73 锁模块lock plate0
74 斜顶angle from pin0
75 斜顶杆angle ejector rod0
76 尼龙拉勾parting locks0
77 复位键、提前回杆early return bar0
78 气阀valves0
79 斜导边angle pin0
80 模排气parting line venting0
81 模总高超出啤机规格mold ba shut height0
82 模胚原身出料位0
cavity direct cut on A-plate，core0
direct cut on B-plate.0
83 不准用镶件Do not u (core/cavity) inrt0
84 用铍铜做镶件u beryllium copper inrt0
85 强度不够insufficient rigidity0
86 公差tolerance0
87 铜公(电极) copper electrode0
动模Movable Mould Moving Half 定模座板Fixed Clamp Plate Top Clamping Plate Top Plate 动模座板Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板Upper Clamping Plate 下模座板Lower Clamping Plate 凹模固定板Cavity-retainer Plate 型芯固定板Mould Core-retainer Plate 凸模固定板Punch-retainer Plate 模套Die Body Die Sleeve Die Blank 支承板Backing Plate Support Plate 垫块Spacer Parallel 支架Ejector Housing Mould Ba Leg 模头 Die Head0
根据国家标准，以下为部分压铸模具术语的标准翻译。0
压力铸造模具Die-Casting Die 压铸模零部件定模Fixed Die Cover Die 定模座板Fixed Clamping Plate 定模套板Bolster Fixed Die 动模Moving Die Ejector Die 动模座板Moving Clamping Plate 直流道Sprue 横流道Runner 内浇口 Gate0
模具分类0
Injection Mold 注塑模Plastic Rubber Mould 塑胶模Rubber Molding 橡胶成形Hot Chamber Die Casting 热室压铸Sand Mold Casting 砂模铸造Extrusion Mold 挤出模Multi-Cavity Mold 多模穴模具Stack Mold, Stack Injection Mould 叠层模Plaster Mold 石膏模Three Plates Mold 三板模Plain Die 简易模Pierce Die 冲孔模Forming Die 成型模Progressive Die 连续模Gang Dies 复合模Shearing Die 剪边模Cavity Die 型腔模Riveting Die 铆合模Compression Molding 压缩成型Flash Mold 溢流式模具Extrusion Mold 挤压式模具Split Mold 分割式模具Mould Cavity 型腔母模Mold Core 模芯公模
Large Die Mold 大型模具Preci Die Mold 精密模具Complex Die Mold 复杂模具Foaming Mould 发泡模具Metal Die 金属模具Plastic Mold 塑料模具Press Tool Stamping Die Punch Die 冲压模具Extrusion Die 挤压模具Graphite Die 石墨模具0
流道浇口部分0
Runner System 浇道系统Sprue Cold Material Trap 浇道冷料井Sprue Puller 拉杆Runner Design 流道设计Main Runner 主流道Secondary Runner 次流道Mould Gate Design 浇口设计Submarine Gate 潜伏浇口Tunnel Gate 隧道式浇口Pinpoint Gate 点浇口Fan Gate 扇形浇口Side Gate 侧浇口Edge Gate 侧缘浇口Tab Gate 搭接浇口Film Gate 薄膜浇口Flash Gate 闸门浇口Slit Gate 缝隙浇口Dish Gate 盘形浇口Diaphragm Gate 隔膜浇口Ring Gate 环形浇口Runnerless 无浇道Sprueless 无射料管方式Long Nozzle 延长喷嘴方式Sprue 浇口，溶渣Insulated Runner Hot Runner 热浇道Runner Plat 浇道模块Valve Gate阀门浇口Slag Well 冷料井Cold Slag 冷料渣Sprue Gate 射料浇口，直浇口
