Die / Tool= 模具 Prog. Die=progressive die 级进模 | Ball bearing guide posts and bushings=球形滚珠导柱和轴套 |
Casting die=铸造模 | Cage=套 |
Part=钣件 | Rigidity=强度 |
Die material=制模材料 | Thin=薄 |
Tool design=模具设计 Strip design=料条设计 | Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R角减少冲头碎裂或模具中有“刀口” |
Tool design approval=模具设计审核 | |
Tool design modification/revision=模具设计更改 | |
Tool parts design (detail) = 模具钣件设计（详细） | Heeled die ts, internally heel form & trim ctions=带箱根的模架，成形与切刃冲头带导引 |
FMC Make=保丽龙制作 | Construction method=结构方法 |
modification= 更改 Check & measure=检查 & 测试 Machining= 机器加工 Large machining=在大型机器上加工上下模架（铣、车等） Small machining=在小型机器上加工模块等 | Lower die trim inrts=下模切刃块 |
Lower trim inrts retainer=下模切刃块承盘 | |
Asmble inrts=组立镶块 | |
Punch stripping plates=冲头压料板 | |
Asmbly=组立 | Trim punch backing plates=切刃冲头背板 |
NC Machining=NC雕刻加工 | Stripper window inrts=料条窗户镶块 |
Fitting=研磨组立 Spotting=合模 | Die tryout=试模 Cushing stroke=缓冲行程 |
Dowel pin=定位销 | Guide lift pin=导引升降销 |
Asmble gas spring=安装氮气缸 | Stamp parts=冲钣件 |
Adjustment=调试 | Run off parts=冲钣件 |
Lower trim steels=下刃块 | Hit parts=冲钣件 |
Section=冲头断面 | Lifters=提升器 |
Trim punch=切刃冲头 | Coil=卷材 |
jack screw hole=起重[千斤顶]螺旋孔 | Guide block=导引块 |
Die t, lower plate=下模架 | Guide the coil through the tool=导引卷材 |
Die t, upper plate=上模架 | layout inspection=全尺寸检验 |
Die inspection & approval=模具检查和审核 | Stretch carriers=拉伸运送装置 |
delivery=发货 | Punch stripping plates=冲头压料板 |
Rejected=拒收 | Trim punch backing plates=切刃冲头背板 |
Scrapped=报废 | Stripper window inrts=料条窗户镶块 |
Rework=返工 | Heel plates=背托 |
stop block=停止块 | Prepare for delivery=准备发货 |
Hydro form 液压成形 | Key=键 |
Shear=剪切 | For locating retainer blocks=承盘键 |
Sensor=传感器 | For holding buttons or pilots=冲母座或导销键 |
Stretch web=拉伸网 | For fixed heel or positive stop=镶根键 |
Layout the parts=设计钣件 | Construction method=结构方法 |
Preceding into the design=继续设计 | Manual Surface Grinder=手动平面磨床 |
Guide the coil through the tool=导引卷材 | Spotting red=合模用丹红 |
Checking aid /checking gage=检具 | Layout ink=试模用蓝墨水 |
Jig=夹具 | Masking tape=黄色不透明胶带(遮蔽胶带) |
Fixture=夹具 | Pliers=尖嘴钳，老虎钳 |
Ball bearing guide posts and bushings= 球形滚珠轴套 | Crent wrench=可调扳手 |
Guide post=导柱Bushings=导套 | Pump pipe=泵管 |
Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R角减少冲头碎裂或模具中有“刀口” | CMM=三次元测量仪 Symmetric=对称的 The axis of symmetry=对称轴 Technical=技术上的 Diagonal=对角线 |
Heeled die ts, internally heel form & trim ctions=带箱根的模架，成形与切刃冲头带导引 | One two three block=一二三模块 Adjustable parallels=可调平行块 Stop block=阻止块 |
Granite Table=花岗岩平台 | Backing Plate=背板 |
Plotter= .描绘器, 图形显示器, 绘图器, 坐标自记 器, 标图员 | Shoulder Bolt=肩头螺丝 (Stripper bolt) |
Belt Sander=带磨机 | Keeper Block=行程块 |
Metal Cutting Band Saw=立式带锯床 | Corner Guide Block=导块 |
Blanchard Grinder=大型平面磨床 | Dowel pin=定位销 |
Joe Blocks=精密量块 | Set Screw=螺塞 |
Whirly Gig=筒夹式冲子成形器 | Jig & fixture =夹具 |
Chamfer Tools=倒角刀具组 | Checking fixture=检具 |
Angle Plate=L形直角座 | Guide Block=导块 |
Gage Pins=英寸塞规 | Plunger=柱塞 |
Sine Plate (magnetic)=正弦磁台 | Pierce=冲孔 |
Flute End Mill=硬质合金钢铣刀 | Wear Strip=耐磨板 |
Mill Cutter=波纹粗铣刀（标准型） | Mating area=组立的接触面 |
C’bore/ counter bore=六角沉头铣刀 | Accommodate=适应 |
Radius Dresr=砂轮修整器 | Wiping hard (very shiny)= 过分摩擦闭合[接触]（闪光） |
Boring Head & Boring Bar=搪孔器、搪刀杆 Pin=销 | Increa the die clearance between the form steels=增加成形块间隙 |
Reamer=绞刀 | Clearance=间隙 |
Approval=确认 | Oil paper=油纸 |
Impact wrench=气动扳手 | 0-11” Micrometer=0-11”千分尺 |
Air pin=空气销 | Trim line=切边 |
bumper [‘bQmpE(r)] n.缓冲器 | +/-0.5mm unless otherwi specified 除非另有规定，否则公差为+/-0.5mm |
Vendor [‘vendE(r), -dC:(r)] n.卖主 | Part tolerance=钣件公差 |
stripper layout=排样图 | Ball no=球刀 |
drawing of panel #987415&16=钣件设计图（公差） | Bore=镗 Line tap=攻丝校直 |
Arbor =柄轴；心轴 | Borer=镗刀，镗床 |
Drill chuck=钻夹头 | Chamfer=倒角 |
Button=冲母座 | Radius=半径 |
Nitrogen Cylinder=氮气缸 | Coolant=切削液 |
Pilot=导销 | Punch=冲头 |
Retainer=承盘 | Distribution Blocks=接头座 |
Button=冲母座 | Screw=螺丝 |
Ho Straps=软管夹（塑料） | Shop=车间 |
Flat Feet Keepers=顶料销 | Crib=仓库 |
Ejector Pin=顶出销 | CNC mill= CNC机床 |
Spring=弹簧 | Jack=千斤顶 |
Straight Port Adapter=直管接头 | Strips=料条 |
Y-205 Ho=软管（塑料） | Styrofoam [`stairEfEum] n.聚苯乙烯泡沫塑料 （保丽龙材料） |
Short Neck Adapter=短接头 | Cut off=落料 |
45。 Swivel= 45。接头(adjustable) | Idle station=空站（for changeability of the part in the future） |
45。Elbow=45。接头(un-adjustable) | Dry run=空转(to check the interference 干涉of a die) |
Compact Swivel Adapter=转接头 | Form=成形 |
Control Panel=控制面板 | Trim=切边 |
Stamp Retainer=承盘 | Perforate= [‘p\:fEreit] v.打孔 |
Spotting press=合模机 | Plumber=水管工人 [‘’plQmE(r)] |
Hand grinder=角磨机 | Yo-yo 卷尺(美) |
Surface grinder=平面磨床 | Drill chuck=钻头夹 |
Blanchard grinder=大型平面磨床 | Tape measure=卷尺 |
End mill=端铣刀/立端刀 | Protractor=量角器 |
Ball no end mill=球头铣刀 | Switch=限位开关 |
Straight edge=直角座 | Caliper=卡尺 |
Shim stock=垫片 | Slug=废料 |
Oversize tap=加大尺寸丝攻 | Fittings=接头 |
Die=模具 | Crimping machine=氮气缸接头夹具 |
Upper die=上模 | Manual surface grinder=手动平面磨床 |
Lower die=下模 | Push cart=推车 |
Die t=模架 | Tool box=工具箱 |
Button die=冲母座 | Heel block=镶根 |
Pilot=导销 | Tap=丝攻 |
Bushing=衬套 | |
Feeler gage=塞尺 | |
HRS=hot roll steel =热轧钢卷 | Belt sander=砂带机 |
CRS=cold roll steel=冷轧钢卷 | Metal cutting band saw=带锯（切割金属） |
Inrt=镶块 | Joe blocks=测量块 |
Guide post=导柱 | Scriber=划线器 |
Crane=吊机 | Zinc coating=镀锌 |
Stripper pad=压料板 | Ball peen hammer=球形榔头 |
Dowel pin=定位销 | Rosin=松香水 |
Heat treat=热处理 Wire burn=线割 | Gage pins= Round cylinders of preci dimension ud for measuring holes. |
Fast wire burn=快走丝 | Blank die=下料模 |
Slow wire burn=慢走丝 | Tryout material=试模材料 |
Stripper pad=压料模 | (Pad retainer) shoulder bolt=stripper bolt=肩头螺丝（all can be ud for guiding a pad） |
Trim block (steel)=切刃块 | Pad retainer=压料模承盘 |
Form block (steel)=成形块 | Drill chuck=钻夹头 |
Drill vice=平口夹钳 | |
Pig putty= epoxy Putty=油灰 | Parallel=平行块/肋条 |
Sandblast=喷沙器 喷沙 (a pressurized air sand mixture) | Graphite =石墨 （lubricant） [‘grAfait] n. |
Plumb= [plQm] n.铅锤, 铅弹 adj.垂直的 vt.使垂直, 用铅增加重量, 探测vi.垂直 | Plumber= n. 水管工人 [‘plQmE(r) |
Solder (lead)= [‘sEuldE(r); (?@) ‘sodEr] n.焊料 v.焊接 (铅条) | Titanium nitrate (Tin coating-hard) =[化]硝酸钛 (钛化处理) |
Binder= ‘baindE(r)] n.环模线，装订工, 包扎者, 包扎工具, | Adjustable locking pliers (vice grip) =可调锁紧老虎钳 |
blind hole=闷眼, 盲孔 | Steel shavings=铁屑 |
slip fit=滑(动)配合 | Cast iron=铸铁 |
sliding chute=滑槽 | Threads=螺纹 |
Ratchet wrench 棘轮扳手 | Spacer block=间隔体(有时也叫平衡块) |
Vi grips=大力钳 | Semi-stripper=半脱件 |
Vargus debur tool=去毛刺器 | Clamp block=楔子 |
Disc grinder=砂轮机 | Killer pin=间隙调节螺栓 |
Air drill=气动手枪钻 | Restrike=整形 |
Hole gage=钻头规 | Extension pin=伸长销 |
Jack screw 起重[千斤顶]螺旋 | Conveyer=输送器 |
Screw hole=螺丝孔 | Spool retainer= 短管扣 |
Pin hole=导销孔 | Guide plate= 导板 |
Sheer cut=剪断 | Guide block= 导块 |
Thrust=推力 | Lock=锁定 |
Heel guide post=跟部导柱 | Preform=预成形 |
Kicker pin=踢出销 | Air bend= 自由弯曲 |
Set height stopper=设定高度阻止器 | Cam cut, cam pierce=剪断加工 |
Knock-out bar=顶出棒 | Gib=嵌条 |
Push-back=推出 | Single roll feed=单滚子进给 |
Cut=切断 | Gripper feed=夹爪进给 |
Pad=托板 | Grip finger=移动爪 |
Brake finger=固定爪 | |
Slide feed=滑动进给 | |
Single gripper feed=单夹爪进给 | |
Hitch feed=紧扣进给 | |
Pinch整缘 | Double roll feed=双滚子进给 |
Flash整缘 | Strip feed=带材进给 |
Wipe down整缘 | Hopper feed=漏斗进给 |
Trim flange整缘 | Station dial feed=分站圆盘进给 |
Horn type整缘 | Friction dial feed=摩擦圆盘进给 |
Shimmy整缘 | Magazine feed=推进器进给 |
Post type=柱型 | Transfer feed=自移进给 |
Solid type=整体型 | Air blow ejector=空气喷出 |
Angle type=折角型 | Kicker=踢出件 |
Composite type=复合型 | Strap=夹条 |
Inrt type=嵌入型 | Engineering=工程 |
Carbide cutters=硬质合金铣刀 | Distance block=平衡块 |
Balance block=平衡块 | |
Washer/shim=垫片 | Pad balancer=平衡块 |
Datum=基准 | Hopper feed= |
Notching punch= 凹口(局部落料)冲头 | French stop(feed stop) =进给停止器 |
End mill=立端刀, 端铣刀 | Transfer punch=洋冲(ud for drilling) |
Neoprene [`ni:Eupri:n] n.[化]氯丁(二烯)橡胶 | Set punch= a male punch shape to transfer to a female punch shape |
Foundry [‘faundri] n.铸造, 翻砂, 铸工厂, 玻璃厂, 铸造厂 | Sand-cast 砂型铸件, 砂型铸造 |
Velocity [vi’lositi] n.速度, 速率, 迅速, 周转率 | Simulation-Draw die drawing 拉伸模设计模拟 |
Ball at=眼泪水 | Square shear=剪板机 |
Draw bead=拉伸筋 | Pitch(progression)=步距 |
Draw lube=拉伸润滑油 | Flange=折边(通常为直边或90º折边)，凸缘 |
Socket(deep & shallow) ratchet= 套筒扳手（深和浅） | Curl=卷边 |
Apex’s=气动扳手 | Channel locks= |
Datum plane=.基准面 | Sand blast=喷砂处理，喷砂设备 |
Plane=平面 | Wrench work=钳工(工作) fitter=钳工 |
Surface=表面 point=点 line=线 | Lathe man=车工 |
Solid=体，固体 | Initiator=开始者,引发剂 |
Body=空心体 | Planar Mill 龙门铣床 Planar [`pleinE(r),-na:(r)] =平面的 |
Graphics Language=图学语言 | Offt=偏置 |
Projection=投影 | Draw=拉伸 |
Esperanto[espE‘rAntEu] =世界语 | Redraw=再拉伸 |
Engineering Drawing=工程图，工程制图 | Blank=下料 |
Graphic Science=图学 | Split=开缝 |
Descriptive Geometry=投影几何 | Notch= 做缺口 |
Reprentation of Diagrams=图表书法 | Separate=切离 |
Blue Print=蓝图 | Emboss=压花 |
Original Drawing=原图 | Joggle=榫接 |
Computer Graphics=电脑绘图 | Hemming=金卯合 |
RAM=记忆体random access memory | Burr= 毛边 |
Plotter=绘图机 | CAM=凸轮工程 |
Geometry=几何 | Hook=吊钩 |
Circle=圆 | Leader=指线 |
Conic ctions=割椎线 | Extension line=延伸线 |
Ellip=椭圆 | Working drawing=工作图 |
Parabola=抛物线 | Full ction=全剖面 |
Hyperbola [hai’pE:bElE] =双曲线 | Half ction=半剖面 |
Straight line=直线 | Broken-out ction=局部剖面 |
Curves=曲线 | Rotated ction=旋转剖面 |
Front view=前视图 | Removed ction=移动剖面 |
Right side view=右侧视图 | Offt full ction=偏置全剖面 |
Left side view=左侧视图 | Auxiliary review=辅助视图 |
Top view=俯视图 | Reference plane=参考平面 |
Bottom view=仰视图 | Projection weld=立式点焊机 |
Rear view=后视图 | Spot weld=点焊 |
Six principal views=六个主要视图 | Dash Panel=前隔板 |
Sectional view=剖视图 | interchangeable fixture=可互换的夹具（可拆卸） |
Blank die=下料模 | nut auto feeder=螺栓自动进料器 |
Transfer die=传送模 | Single gun=单枪 |
Clamping slot=U沟 | quentially welded=按顺序焊接 |
Spring pin=弹簧导销 | stud projection welding machine=单植钉点焊机 |
Sensors that determine part location=钣件定位的限位开关 | welding fixture=焊夹具 |
part gauging（gauge）=钣件定位规 | PLC控制器=可控程式器 |
cutting clearance=切边间隙 | gyroscopic suspension=葫芦悬架 |
heavy -C- frame steel machine body construction =重负载C型架钢体机构 | dual quence weld control=双向焊接控制器 |
pneumatic clamping=气缸夹钳 | overhead frames/gantries with trolley= 上置式机架并带有吊枪用触轮 |
part prence nsing=钣件传感器 | aler dispensing unit=封闭排种机构 |
Panel Back Upper=后窗上补强件 | Handling hole=起吊孔 |
Bracket=补强件 | Tack weld=点焊 |
Nut=螺帽 | Bender pad=拉伸压料板 |
Stud=螺钉 | Stripper bolt=压料螺栓 Pad retainer=压料螺栓(两种) |
Bolt=螺丝 | Interference＝干涉 |
Go 1=design approval, but not fabricate | |
Go 2=building approval (fabricate) | |
Bulkhead=隔板 | |
Fast pitch= | |
Draw quality, special killed=拉伸质量，特别裁断 | |
Scallop=粗糙度=cusp=两曲线的交点,尖点 [‘skolEp] | |
Specify=指明 | |
Normalize=调质（热处理解除内应力） | |
Co-Axial Centering Indicator=寻边器 | |
Hemming=卷边 | |
本文发布于:2023-05-11 08:04:56，感谢您对本站的认可！
本文链接：https://www.wtabcd.cn/fanwen/fan/82/582646.html
版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系，我们将在24小时内删除。
| 留言与评论（共有 0 条评论） |
