________________________________________________________________________
--
ABN 96 108 552 325
WELD SYMBOLS AS1101.3
焊接符号澳大利亚标准1101.3
TKMH DRAWING WELD SYMBOL EXPLANATION
克虏伯图纸焊接符号解释
________________________________________________________________________
--ABN 96 108 552 325
- Single Sided fillet weld -单面角焊缝
- Number indicates the weld leg length -号码表示焊脚尺寸大小
- If there is a gap between the items, the fillet size must be incread by the size of the gap.
-如果两个件有间隙，角如何修眉
焊缝尺寸也随间隙尺寸而增加
- Double Sided fillet weld -双面角焊缝
- Number indicates the weld leg len春节大餐菜谱
gth -号码表示焊脚尺寸大小
- If there is a gap between the items, the fillet size must be incre普者黑主要3个景点
ad by the size of the gap. -如果两个件有间隙，角焊缝尺寸也随间隙尺寸而增加
- Partial Penetration Welds from One Side -单面部分熔透焊接
- No Weld Gap Required -没有焊接间隙要求
- Number Indicates the weld penetration depth -号码表示坡口深度
- Partial Penetration Weld from Two Sides -双面部分熔透焊接
- No Weld Gap Required. -没有焊接间隙要求
- Number ind班总结
icates the bevel depth. -号码表示坡口深度
________________________________________________________________________
--ABN 96 108 552 325
- Complete Penetration Weld from One Side
-
单面全熔透焊接
- Minimum Weld Gap (Root Opening) of 2mm or as specified by the WPS&nb英语四级查分
sp; and drawing
-最小焊接间隙2mm （开根），或者按照焊接工艺规程以及图纸要求留间隙。
-
If there is no weld gap the fit up will be rejected and the items are to be disasmbled and t up with weld gaps.
-如果没有焊接间隙，克虏伯将拒收，需要将部件拆下来重新留焊接间隙然后再焊。
________________________________________________________________________
--ABN 96 108 552 325
- Full Penetration Weld from Both Side山药的功效和作用
s -双面全熔透焊接
- Minimum Weld Gap (Root Opening) of 2mm or as specified by the WPS
-
最小焊接间隙2mm （开根），或者按照焊接工艺规程以及图纸要求留间隙。
- If there is no weld gap the fit up will be rejected文章
and the items are to脚踝肿是什么原因
be disasmbled and t up with weld gaps.
-如果没有焊接间隙，克虏伯将拒收，需要将部件拆下来重新留焊接间隙然后再焊。
Complete Joint Penetration Required 完成接头全熔透焊的要求
Where no depth of groove preparation or design throat thickness is shown on the welding symbol for single-butt and symmetrical double-butt welds, complete joi股藓
nt preparation is required (e Figure 4.6 (d) & (e)). 对于单面对接和双面对称对接焊，没有坡口或焊肉深度的焊接符号，请按照图4.6(d) 和(e)完成接头的坡口准备
FIGURE 4.6 DESIGNATION OF DESIGN THROAT THICKNESS OF BUTT WELDS
图4.6 对接焊设计焊肉符号
