ASTM D3330 中英文对照版
手机死机
Designation: D 3330/D 3330M –网上大学 00
名称：D 3330/D 3330M-00
Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape1
压敏胶带剥离强度测试标准
This standard is issued under the fixed designation D 3330/D 3330M; the number immediately following the designation
indicates the year of original adoption or, in the ca of revision, the year of last revision. A number in parenthes indicates the
year of last reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
此标准是根据D 3330/D3330M 整理修订；名称后面的数字代表首发年份。括号内为最近修订年份。带有上标e 表
示最后一次发行或修订时的改动之处。
1. 1. Scope
1．1 范围
1. 1.1 The test methods cover the measurement of the peel adhesion of pressure-nsitive tapes.
1.1.1 这些测试方法主要是针对压敏胶带剥离强度的测试
1. 1.1.1 Test Method A gives a measure of the adherence, when peeled at 180° angle, to a standard steel panel or to other surface
钾含量高的食物of interest for a single-coated tape.（加载板）
1.1.1.1 方法A 是压敏胶带从一标准金属板180°剥离测试方法；------------
2. 1.1.2 Test Method B gives a measure of the adherence to the backing of a single-coated tape.
2.1.1.2 方法B 是测试单面背衬胶的粘性
3. 1.1.3 Test Method C gives a measure of the adherence of double-coated tape to a standard steel panel or other surface of
interest.
3.1.1.3 方法刻舟求剑C 是双面背衬胶与标准金属板的粘性测试方法；
4. 1.1.4 Test Method D gives a measure of the adherence of the relea liner to the adhesive of either single-or double-coated
tape.
4.1.1.4 方法D 是测试单面或者双面背衬胶离型纸的粘性
5. 1.1.5 Test Method E gives a measure of the adherence of an adhesive transfer tape to a standard steel panel or other surface of
interest.
5.1.1.5 方法E 是测试无基材胶带与标准金属板之间的粘性
6. 1.1.6 Test Method F gives a measure of the adherence, when peeled at 90° angle, to a standard steel panel or other surface of
interest for a single-coated tape.
6.1.1.6 方法F 是测试胶带90°剥离方法；
7. 1.2 The test methods provide a means of asssing the uniformity of the adhesion of a given type of pressure-nsitive
adhesive tape. The asssment may be within a roll of tape, between rolls, or between production lots.大豆卵磷脂胶囊
7.1.2 这些测试方法，是胶带的统一的评定方法；----------
8. 1.3 Variations in either the tape backing or the adhesive, or both, affect the respon. Therefore, the test methods cannot be
ud to pinpoint the specific cau(s) of non-uniformity.
9. 1.4 The test methods may not be appropriate to test tapes having relatively stiff backings, stiff liners, or backings showing
high stretch at low forces. The characteristics will result in a high variability for the test respon which is not a true indication
of the real nature of the adhesive bond.
10. 1.5 Values stated in either SI or inch-pound units are to be regarded parately as standard. The values stated in each system
may not be exact equivalents, therefore, each system must be ud independently witho
ut combining values in any way.
工地模板
11. 1.6 The test methods are intended to replace AFERA 4001, EN 1939, PSTC-1,
PSTC-2, PSTC-3 and PSTC-4.
1.7 This standard does not purport to address all of the 1 The test methods are under the jurisdiction of ASTM Committee D-10
一袋大米重多少千克on Packaging and are the direct responsibility of Subcommittee D10.14 on Tape and Labels. Current edition approved Oct. 10,
2000. Published December 2000. Originally published as D 3330 – 76. Last previous edition D 3330/D 3330M – 99. Copyright .
ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, United States. safety concerns, if any, associated with its
u. It is the responsibility of the ur of this standard to establish appropriate safety and
health practices and determine the
applicability of regulatory limitations prior to u.
2. Referenced Documents
2.1 ASTM Standards: A 666 Specification for Austenitic Stainless Steel, Sheet, Strip, Plate and Flat Bar2 D 996 Terminology of
Packaging and Distribution Environments3 D 3715/D 3715M Practice for Quality Assurance of Pressure-Sensitive Tapes3 D
4332 Practice for Conditioning Containers, Packages or Packaging Components for Testing3 D 5750 Guide for Width and
Lengths of Pressure-Sensitive Tape3 E 122 Practice for Choice of Sample Size to Estimate a Measure of Quality for a Lot or
Process4
2.2 AFERA Standard:5 4001 Self adhesive tapes – Measurement of peel adhesion
2.3 European Norm:6 EN 1939 Self adhesive tapes –it的宾格是什么 Measurement of peel adhesion from stainless steel or from its own backing
