page 1 of 2
日本动漫专业MATERIAL DATA SHEET如果如果
LG/ 02.2010 EDITION 6
TARNOFORM® 300
PROPERTIES STANDARD ISO 11357-1-3 1183 1133 1133 62 62 294-4 527-1,-2 527-1,-2 527-1,-2 527-1,-2 178 178 179-1 179-1 179-1 179-1 180 2039-1 306 75-1,-2 11359-1/-2 IEC 60216 UL94 US-FMVSS 302 IEC 60093 IEC 60093 IEC 60243-1 IEC 60250 IEC 60250 IEC 60112 TEST CONDITIONS 10°C/min. 190°C/2,16kg 190°C/2,16kg 23°C/50%RH 23°C/sat. 60x60x2 50mm/min 50mm/min 50mm/min 1mm/min 2mm/min 2mm/min 1eU 1eU 1eA 1eA 358 N 50N 1,8 MPa 23°C - 55°C 20000 h 5000 h 3,2 mm thickness d≥1mm 2mm 1MHz 1MHz solution A UNIT TYPICAL DATA
PHYSICAL Melting point; DSC Density Melt volume-flow rate (MVR) Melt mass-flow rate (MFR) Humidity absorption Water absorption Linear shrinkage II MECHANICAL Tensile strength at yield Elongation at yield Elongation at break Tensile E-modulus Flexural strength Flexural modulus Charpy impact strength Charpy impact strength (-30°C) Charpy notched impact strength Charpy not
ched impact strength (-30°C) Izod notched impact strength Ball indentation hardness THERMAL Vicat softening point Heat deflection temperature Coefficient of linear thermal expansion II Temperature index TI Limit of temperature, at few hours operation FLAMMABILITY Flammability Burning Rate ELECTRICAL Surface resistivity Volume resistivity Dielectric strength Dielectric constant Dissipation factor Comparative tracking index CTI Ω Ωxcm kV/mm V 10 15 10 25 3,8 600
14
资本形成总额°C 3 g/cm 3 cm /10min g/10min % % % MPa % % MPa MPa MPa 2 kJ/m 2 kJ/m 2 kJ/m 2 kJ/m 2 kJ/m MPa °C °C E-4/°C °C °C °C Class mm/min共赢发展
167 1,41 8 9 0,2 0,8 2,0 62 10 50 2800 64 2500 200 180 6 5,5 6 145 150 115 1,1 100 HB <100
Product nomenclature acc. ISO 9988-1: POM-K, M-GNR, 03-002
All data for natural and black coloured material (unless indicated otherwi). Properties measured at 23°C (unless indicated otherwi).
\
燕雀安知page 2 of 2
TARNOFORM® 300
木星的无奈CHARACTERISTICS Tarnoform® 300 - is the standard, fast cycling injection-moulding grade, good chemical resistance, exhibit low mould deposit. Destined for injection moulding for production of parts ud in automotive, machine parts, appliances, houhold articles, electronic, building and furnishes industries, etc. Melt temperature: 170-230°C, Injection pressure: 60-120 MPa, Injection speed: slow - medium Mould temperature: 60-120°C, optimum about 90°C, for precision parts up to 120°C Tarnoform® 300 is delivered as ready for processing, without need of drying. If product has been expod to a damp atmosphere or has been in contact with water, it has to be dried at 100° C to 120° C in circulating air oven for about 2- 4 hours. Processing moisture content should be : < 0,10 %, Standards colours: natural, black, other colours on request.消毒饮
APLICATIONS
PROCESSING
DRYING
COLOUR波刺毛
RECYCLING
Clean, milled, not contained degradated polymer, postproduction wastes could be reud after mixing with fresh plastic. The addition level of milled scraps may reach up to 10%. It is recommended to u pre-dry milled scraps. Available in PE bags containing 25 kg of granules and next put to 1000 kg pallets Available in octabins (big-bag containers) containing up to 1000 kg of granules
PACKAGING
