物性表1000

更新时间:2023-07-22 09:40:25 阅读: 评论:0

U LTEM™ Resin 1000
有排卵为什么不怀孕A sia Pacific: COMMERCIAL
Transparent, standard flow Polyetherimide (Tg 217C). UL94 V0, V2 and 5VA listing. Effective June, 2007 this grade will no longer be supported with
biocompatibility information and should not be ud for medical applications which require biocompatibility. Alternative grade HU1000. For US FDA and EU Food Contact compliance, plea lect 1000F resin.
TYPICAL PROPERTIES¹
TYPICAL VALUE Unit Standard
M ECHANICAL
T ensile Stress, yld, Type I, 5 mm/min
110
M Pa A STM D 638T ensile Strain, yld, Type I, 5 mm/min 7%A STM D 638T ensile Strain, brk, Type I, 5 mm/min 60%A STM D 638T ensile Modulus, 5 mm/min
3580M Pa A STM D 638F lexural Stress, yld, 2.6 mm/min, 100 mm span 165M Pa A STM D 790F lexural Modulus, 2.6 mm/min, 100 mm span 3510M Pa A STM D 790H ardness, Rockwell M
109-A STM D 785T aber Abrasion, CS-17, 1 kg
10
m g/1000cy A STM D 1044
I MPACT
Izod Impact, unnotched, 23°C
1335
J /m A STM D 4812 Izod Impact, notched, 23°C
53J /m A STM D 256I zod Impact, Rever Notched, 3.2 mm 1335J /m A STM D 256 Gardner,  23°C
36
J A STM D 3029
T HERMAL
V icat Softening Temp, Rate B/50
218
°C A STM D 1525H DT, 0.45 MPa, 6.4 mm, unannealed 210°C A STM D 648H DT, 1.82 MPa, 6.4 mm, unannealed 201
°C A STM D 648 CTE, -20°C to 150°C, flow 5.58E-051/°C A STM E 831 CTE, -20°C to 150°C, xflow 5.4E-051/°C A STM E 831T hermal Conductivity
0.22W /m-°C A STM C 177R elative Temp Index, Elec
170°C U L 746B R elative Temp Index, Mech w/impact 170°C U L 746B R elative Temp Index, Mech
w/o impact
170
°C
U L 746B
Source GMD, last updated:
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES ( S ELLER ) ARE SOLD SUBJECT TO SELLER S  STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST.  INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH.  HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER S
  MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS.  UNLESS OTHERWISE PROVIDED IN SELLER S
STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT. Each ur is responsible for making its own determination as to the suitability of Seller s  materials, products, rvices or recommendations for the ur s  particular u through appropriate end-u and other testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller s  Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. Statements by Seller concerning a possible u of any material, product, rvice or design do not, are not intended to, and should not be construed to grant any licen under any patent or other intellectual property right of Seller or as a recommendation for the u of any material, product, rvice or design in a manner that infringes any patent or other intellectual property right. SABIC and brands marked with ™ are trademarks of SABIC or its subsidiaries or affiliates.(1) Typical values only. Variations within normal tolerances are possible for various colors.  All values are
measured after at least 48 hours storage at 23°C/50% relative humidity.  All properties, except the m
elt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for lection purpos.  Not to be ud for part or tool design.
(3) This rating is not intended to reflect hazards prented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon.  Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design.  It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.(6) Needs hard coat to consistently pass 60 c Vertical Burn.
U LTEM™ Resin 1000
A sia Pacific: COMMERCIAL
TYPICAL PROPERTIES¹
TYPICAL VALUE Unit Standard
P HYSICAL
S pecific Gravity
1.27
-A STM D 792W ater Absorption, 24 hours
0.25%
A STM D 570W ater Absorption, equilibrium, 23C 1.25%A STM D 570M old Shrinkage, flow, 3.2 mm (5)0.5 - 0.7%
S ABIC Method  Melt Flow Rate, 337°C/6.6 kgf
9
g /10 min A STM D 1238
E LECTRICAL
V olume Resistivity
1.E+17
O hm-cm A STM D 257D ielectric Strength, in air, 1.6 mm
32.7k V/mm A STM D 149D ielectric Strength, in oil, 1.6 mm 28k V/mm A STM D 149D ielectric Strength, in oil, 3.2 mm 19.7k V/mm A STM D 149R elative Permittivity, 100 Hz 3.15-A STM D 150R elative Permittivity, 1 kHz 3.15-A STM D 150D issipation Factor, 100 Hz 0.0015-A STM D 150D issipation Factor, 1 kHz
0.0012-A STM D 150D issipation Factor, 2450 MHz 0.0025-A STM D 150A rc Resistance, Tungsten {PLC}5P LC Code A STM D 495H ot Wire Ignition {PLC)
肉丝炒粉1P LC Code U L 746A H igh Voltage Arc Track Rate {PLC}2P LC Code U L 746A H igh Ampere Arc Ign, surface {PLC}3P LC Code U L 746A C omparative Tracking Index (UL) {PLC}
4
P LC Code U L 746A
F LAME CHARACTERISTICS
U L Recognized, 94V-2  Flame Class Rating (3)
0.4
m m U L 94U L Recognized, 94V-0  Flame Class Rating (3)
团队名称霸气0.75m m U L 94U L Recognized, 94-5VA Rating (3)3m m U L 94O xygen Index (LOI)
47
%
A STM D 2863
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES ( Source GMD, last updated:
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.
S ELLER ) ARE SOLD SUBJECT TO SELLER S  STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST.  INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH.  HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER S  MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS.  UNLESS OTHERWISE PROVIDED IN SELLER S
STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT. Each ur is responsible for making its own determination as to the suitability of Seller s  materials, products, rvices or recommendations for the ur s  particular u through appropriate end-u and other testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller s  Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. S
tatements by Seller concerning a possible u of any material, product, rvice or design do not, are not intended to, and should not be construed to grant any licen under any patent or other intellectual property right of Seller or as a recommendation for the u of any material, product, rvice or design in a manner that infringes any patent or other intellectual property right.(1) Typical values only. Variations within normal tolerances are possible for various colors.  All values are
measured after at least 48 hours storage at 23°C/50% relative humidity.  All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for lection purpos.  Not to be ud for part or tool design.
(3) This rating is not intended to reflect hazards prented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon.  Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design.  It is recomm
ended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.(6) Needs hard coat to consistently pass 60 c Vertical Burn.
U LTEM™ Resin 1000
A sia Pacific: COMMERCIAL
TYPICAL PROPERTIES¹
TYPICAL VALUE Unit Standard
F LAME CHARACTERISTICS
N BS Smoke Density, Flaming, Ds 4 min
0.7
-
A STM E 662
Source GMD, last updated:
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES ( S ELLER ) ARE SOLD SUBJECT TO SELLER S  STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST.  INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH.  HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER S  MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS.  UNLESS OTHERWISE PROVIDED IN SELLER S
STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDAT
IONS DESCRIBED IN THIS DOCUMENT. Each ur is responsible for making its own determination as to the suitability of Seller s  materials, products, rvices or recommendations for the ur s  particular u through appropriate end-u and other testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller s  Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. Statements by Seller concerning a possible u of any material, product, rvice or design do not, are not intended to, and should not be construed to grant any licen under any patent or other intellectual property right of Seller or as a recommendation for the u of any material, product, rvice or design in a manner that infringes any patent or other intellectual property right.(1) Typical values only. Variations within normal tolerances are possible for various colors.  All values are
measured after at least 48 hours storage at 23°C/50% relative humidity.  All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for lection purpos.  Not to be ud for part or tool design.
(3) This rating is not intended to reflect hazards prented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon.  Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design.  It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.(6) Needs hard coat to consistently pass 60 c Vertical Burn.
U LTEM™ Resin 1000
A sia Pacific: COMMERCIAL
PROCESSING PARAMETERS
TYPICAL VALUE Unit
I njection Molding
立时的近义词D rying Temperature 150°C D rying Time
4 - 6h rs D rying Time (Cumulative)24h rs M aximum Moisture Content 0.02
%M elt Temperature 350 - 400°C N ozzle Temperature
345 - 400°C F ront - Zone 3 Temperature 345 - 400°C M iddle - Zone 2 Temperature 340 - 400°C R ear - Zone 1 Temperature 330 - 400°C M old Temperature 135 - 165°C B ack Pressure 0.3 - 0.7M Pa S crew Speed
40 - 70r pm S hot to Cylinder Size 40 - 60
%V ent Depth
0.025 - 0.076m m E xtrusion Blow Molding
D rying Temperature 140 - 150°C D rying Time
4 - 6h rs D rying Time (Cumulative)24
h rs M aximum Moisture Content 0.01 - 0.02%M elt Temperature (Parison)320 - 355°C B arrel - Zone 1 Temperature 325 - 350°C B arrel - Zone 2 Temperature 330 - 355°C B arrel - Zone 3 Temperature
如何践行工匠精神330 - 355°C B arrel - Zone 4 Temperature 330 - 355°C A dapter - Zone 5 Temperature 330 - 355°C H ead - Zone 6 - Top Temperature 330 - 355°C H ead - Zone 7 - Bottom Temperature 330 - 355°C S crew Speed
10 - 70
r pm
• DO NOT purge with low melting styrene or acrylic resins.• Up to 30% Regrind has been successfully reprocesd.
Source GMD, last updated:
伍舜德PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES ( S ELLER ) ARE SOLD SUBJECT TO SELLER S  STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST.  INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH.  HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENT
ATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER S  MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS.  UNLESS OTHERWISE PROVIDED IN SELLER S
STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT. Each ur is responsible for making its own determination as to the suitability of Seller s  materials, products, rvices or recommendations for the ur s  particular u through appropriate end-u and other testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller s  Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. Statements by Seller concerning a possible u of any material, product, rvice or design do not, are not intended to, and should not be construed to grant any licen under any patent or other intellectual property right of Seller or as a recommendation for the u of any material, product, rvice or design in a manner that infringes any patent or other intellectual property right.(1) Typical values only. Variations within normal tolerances are possible for various colors.  All values are
measured after at least 48 hours storage at 23°C/50% relative humidity.  All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
弟子规读后感(2) Only typical data for lection purpos.  Not to be ud for part or tool design.
(3) This rating is not intended to reflect hazards prented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon.  Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design.  It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.(6) Needs hard coat to consistently pass 60 c Vertical Burn.
U LTEM™ Resin 1000
A sia Pacific: COMMERCIAL
PROCESSING PARAMETERS
TYPICAL VALUE Unit
E xtrusion Blow Molding
M old Temperature 65 - 175°C D ie Temperature
325 - 355
常德美食°C
• DO NOT purge with low melting styrene or acrylic resins.• Up to 30% Regrind has been successfully reprocesd.
Source GMD, last updated:
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES ( S ELLER ) ARE SOLD SUBJECT TO SELLER S  STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST.  INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH.  HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER S  MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS.  UNLESS OTHERWISE PROVIDED IN SELLER S
STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT. Each ur is responsible for making its own determination as to the suitability of Seller s  materials, products, rvices or recommendations for the ur s  particular u through appropriate end-u and other testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller s  Standard
Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. Statements by Seller concerning a possible u of any material, product, rvice or design do not, are not intended to, and should not be construed to grant any licen under any patent or other intellectual property right of Seller or as a recommendation for the u of any material, product, rvice or design in a manner that infringes any patent or other intellectual property right.(1) Typical values only. Variations within normal tolerances are possible for various colors.  All values are
measured after at least 48 hours storage at 23°C/50% relative humidity.  All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for lection purpos.  Not to be ud for part or tool design.
(3) This rating is not intended to reflect hazards prented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon.  Actual shrinkage may vary outside of range d
ue to differences in processing conditions, equipment, part geometry and tool design.  It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.(6) Needs hard coat to consistently pass 60 c Vertical Burn.

本文发布于:2023-07-22 09:40:25,感谢您对本站的认可!

本文链接:https://www.wtabcd.cn/fanwen/fan/82/1110555.html

版权声明:本站内容均来自互联网,仅供演示用,请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系,我们将在24小时内删除。

标签:霸气   践行   排卵   肉丝   读后感   团队   精神
相关文章
留言与评论(共有 0 条评论)
   
验证码:
推荐文章
排行榜
Copyright ©2019-2022 Comsenz Inc.Powered by © 专利检索| 网站地图