T echnical data Rubber Compounds
Performance Test Results
Contents
■Silicone rubber
General
properties 2
properties 5 Other
■Fluorosilicone rubber 6■SEP rubber 7■Curing agents
Types 8 Suitability by application 8 Standard addition quantity 9■Standard conditions for compression molding 10■Primers 10■Coloring agents 10■Application examples by industry 11
21. Silicone rubber: general properties怀孕初期恶心
Measurement: in accordance with JIS K 6249 Test pieces: 165°C/10 min (press cure), 200°C/4 h (post cure)
杜聿明简介✽1 Standard addition quantity is the quantity of curing agent added to 100 parts compound.
✽2 Linear shrinkage values differ according to the curing agent ud.
✽3 Angle piece
✽4 Measured values at 150°C/22 h.
✽5 The data below linear shrinkage is bad on measurements on a product by compression molding at 170°C/10 min (with no post cure).
[Unit conversion] tensile strength: 10 kgf/cm2 = 0.98 MPa; tear strength: 1 kgf/cm = 0.98 kN/m; volume resistivity: 1014 Ω·cm = 1 TΩ·cm.
(Not specified values)
(Not specified values)
3
Measurement: in accordance with JIS K 6249 Test pieces: 165°C/10 min (press cure), 200°C/4 h (p
ost cure)✽1 Standard addition quantity is the quantity of curing agent added to 100 parts compound.✽2 Linear shrinkage values differ according to the curing agent ud.✽3 Test pieces: 120°C/10 min (press cure), 200°C/4 h (post cure)
牛奶解酒
✽4 For addition quantities, refer to Standard Addition Quantity of curing agents on p. 9.✽5 Measured values at 100°C/22 h ✽6 Measured values at 150°C/22 h ✽7 X-93-1609 is a flame retardant.
[Unit conversion] tensile strength: 10 kgf/cm 2 = 0.98 MPa; tear strength: 1 kgf/cm = 0.98 kN/m; volume resistivity: 1014 Ω·cm = 1 T Ω·cm.
(Not specified values)
(Not specified values)
4Silicone rubber: General properties (cont.)
Measurement: in accordance with JIS K 6249 Test piece: 165°C/10 min (press cure), 200°C/4 h (post cure)
✽1 Standard addition quantity is the quantity of curing agent added to 100 parts compound.前滚翻的动作要领
✽2 Linear shrinkage values differ according to the curing agent ud.
✽3 Test pieces: 120°C/10 min (press cure), 200°C/4 h (post cure)
什么的寒风
✽4 Test pieces: 120°C/10 min (press cure), 150°C/1 h + 250°C/24 h (post cure)
✽5 Test pieces: 120°C/10 min (press cure), 150°C/1 h (post cure)
耳石症症状
✽6 Angle piece ✽7 Measured values at 150°C/22 h ✽8 Ω·m ✽9 Measured values at 150°C/70 h ✽10 Measured values at 105°C/70 h
[Unit conversion] tensile strength: 10 kgf/cm2 = 0.98 MPa; tear strength: 1 kgf/cm = 0.98 kN/m; volume resistivity: 1014 Ω·cm = 1 TΩ·cm.
(Not specified values)
(Not specified values)
5
(Not specified values)
爱迪生救妈妈(Not specified values)
Measurement: in accordance with JIS K 6249 Test pieces: 165°C/10 min (press cure), 200°C/4 h (post cure)中药材种植指南网
✽1 Measured values at 200°C/72 h ✽2 Measured values at 230°C/72 h ✽3 Test pieces: 120°C/10 min (press cure), 200°C/4 h (post cure)
✽4 Measured values at 300°C/72 h ✽5 Relevant data is for addition cure (C-25A/B=0.5/2.0)
✽6 Data for the product in question was measured bad on a pressure-cure product cured at 170°C/10 min (with no post cure).
(Not specified values)
Measurement: in accordance with JIS K 6249 Test pieces: 165°C/10 min (press cure), 200°C/4 h (post cure)
(Not specified values)
