注塑、模具专业英语
Surface Appearance外观
Glossiness/gloss finish光洁度、粗糙度
Matt finish/matt surface毛面
Glass fiber rich surface/glass emergence on the surface玻纤外露、浮纤Blooming/surface blooming表面析出
White patches on surface表面白斑
Silver marks/silver streak银纹
Splay mark水纹、料花
Flow mark流纹
Brittle/brittleness脆、脆性
Bubbles/trapped gas气泡/困气
苯妥英钠副作用Void孔、气泡
Burn marks烧伤
FR failed阻燃不合格
Flame rating V-2阻燃等级V-2
Poor dispersion分散不好
FR/PTFE …agglomerates etc阻燃剂/PTFE…结块
Pellet porous颗粒料孔隙、
Low impact/tensile strength etc低冲击强度/拉伸强度等
High flow/filler content etc高流动性/过度填充
Longs/fines/doubles长粒/碎屑/连粒
Poor cut粒形不好柏拉图理念论
Bristle/voids表面有小气泡/孔
Glass bundles纤维结团
Product was rejected due to 产品不能接受因为…
High moisture level高水分、高湿度
Warpage/warped翘曲/变形
Shrinkage/shrink收缩/收缩率
Sink marks凹陷、缩水
Short shot/short molding打不满、欠注
Distortion变形
Over dimension尺寸过大
Under dimension尺寸过小
Flashing飞边、披锋、溢边
Discoloration变色
Off color颜色差异
Flow rate流动速率
Viscous/viscosity粘性的、粘的/黏度
High flow高流动
Low flow低流动
Sticky粘的，粘性的
Sticking core粘后模，粘模芯
Sticking sprue粘水口
Sticking cavity粘前模
Mold relea（agent）脱模(剂)
Antioxidant抗氧剂
Flame retardant agent阻燃剂
Heat stabilizer热稳定剂
Chopped glass fiber短切玻纤
Roving glass fiber粗纱/长玻纤
Glass beads玻璃微珠
Milled fiber碾磨纤
Molybdenum disulfide/moly/MoS2二硫化钼Colorant着色剂
Pigment颜料
Dye染料
Accepted product specification接受产品规格Approved our product认可我们的产品
Re-t spec重新定标准
Add in extra …添加多一点…
Reduced …content减少…含量
Dropped/reduced …by x％减少…含量…％Confirmed color standard确认颜色标准
Approved color standard认可颜色标准
Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品
Undergoing heat aging test在做热老化实验
Product is under testing产品在测试当中
Received first order接了第一个定单
Expected to finish by …预计在…完成
Expected order is xMT预计定单量…吨
Estimated annual/monthly consumption预计年/月用量模具方面：
Ejection system顶出系统、脱模系统
pin顶针、推杆
spring弹簧
Gate type浇口类型
Sprue主流道
健美体操
runner分流道讨薪找哪个部门最有效
cavity模腔
Sprue gate直浇口
四化建设是哪四化Pin point gate点浇口
Tab gate护耳浇口
Fan gate 扇形浇口
Tunnel or submarine gate潜伏式浇口
Jump gate跳跃式浇口Diaphragm gate片状浇口
Ring gate 环形浇口
The cavity of the mould模腔
汉朝宫殿Heated cylinder加热料筒
Surface finish表面光洁度
Sink mark缩水
Air trap困气
Gas trapped气体困着，困气
void空隙，孔
galling烧焦
Weld line熔接痕，熔合线
Drag mark划伤、脱模痕
Scratch mark模具刮花
关于水的句子Deformed/ warp变形
Ejector not returned顶针不回位slide滑块、行位
streak波纹、条纹、色痕delamination分层
Jetting mark喷射痕
Gate mark浇口痕
rib筋、加强筋、骨位
boss凸台、凸起、凸痕
Melt flow length熔体流线长度Ejector plate顶针板
Stop pin限位销
Push rod推杆、顶针
Push back pin复位杆
Ejector guide pin顶针导柱
Cold-slug-well冷料井、冷料穴
plate模板
Ejected mark顶痕，顶白
nozzle喷嘴
Surface defect表面缺陷
Air vent排气口
Filling uneven走胶不平衡、进胶不平衡pressure：压力
speed：速度
control：控制
protection pressure：保压
mold：模
t：设定
option：选择
injection：射胶
pressure reducing valve ：减压阀relief valve：泄压阀
max：最大
状物作文600字max：最大
system：系统proportional：比例pressure transducer：压力传感器sampling试模
pressure nsor压力感应器AMP 伺服放大器
trial run
running
gate
dosage 溶胶
clamp open 开模
