Hitachi Compressor Products (Guangzhou) Co.,Ltd.
编号：HCPG09-*** Date: 2009-02-10
涡旋压缩机技术规格书
Specification for Scroll Compressor婚前财产协议
Model: E605DH-59D2YG
广州日立压缩机有限公司
编 制
审 核
批 准
客户名称：
客户确认
确认日期
空调器型 号
1．规格 Specification
1.1 压缩机 Compressor
辽宁高考分数压缩机型号 Compressor Model E605DH-59D2YG
压缩机型式 Compressor Type 全封闭型电动压缩机 Hermetic Motor Compressor 压缩机方式 Compression Type 涡旋式 Scroll Type
使用冷媒 Refrigerant R410A
排气容积 Displacement 59cm3/rev
润滑油 / 油量 Oil / Oil Charge FVC68D / 500ml
涂装 Painting 黑色 Black Color Paint
总质量(含油) Net Mass(Including Oil) 41kg
吸气管接口内径 Suction Accept I.D Ф19.3mm
排气管接口内径 Discharge Accept I.D Ф12.9mm
※备注：由于压缩机出厂油量只有500ml，在并联使用时要追加牌号为FVC68D的冷冻机油。
参考追加值为10HP～12HP系统追加3.0L，16HP系统追加4.0L。
1.2 电机 Motor
电动机型式 / 起动方式 Motor Type / Start Mode
三相感应电机 / 直接
3 Pha Induction Motor / Direct Start
极数 Pole 2极 2 Poles
额定电压 / 频率Rated Voltage / Frequency 3Ph–380～415V-50Hz / 3Ph–440V-60Hz
额定转数 Rated Revolution 2,880rpm [50Hz] / 3,470rpm [60Hz]
绝缘等级 Insulation Class E级 E Class
绕组阻抗 Winding Resistance (at 20℃) 2.760±7%Ω
1.3 性能 Performance
冷凝温度 Condensing temp.：54.4 ℃ 蒸发温度 Evaporating temp.：7.2 ℃
回气温度 Return gas temp.：18.3 ℃ 周围温度 Ambient temp.：35.0 ℃手抄报热爱祖国
膨胀阀前液体温度 Liquid temp.：46.0℃
1.4 一般特性 Characteristics
气密试验压力 Leak Tight Pressure 4.2MPa[高压侧H.P. Side] / 2.2MPa[低压侧L.P. Side]耐压试验压力Hydrostatic Strength Pressure 6.3MPa[高压侧H.P. Side] / 3.3MPa[低压侧L.P. Side]绝缘阻抗 Insulation Resistance 10MΩ Min.
绝缘耐压 Withstand Voltage 1,830V-1min.
残余水分量 Residual Moisture 350mg Max.
大耳朵图图的图片2. 压缩机配件 Accessories Of Compressor
NO. 名称 Parts Name 数量 Qty 代号 Drawing NO. 备注 Remarks
1 支撑螺栓 Blot 4 CSE00289
2 防震胶垫 Rubber Grommet B 4 CSE00290
3 防震胶座 Rubber Grommet A
4 CSD00292
4 垫圈 Washer 4 CSE00303
5 M6螺母 M
亚洲丁香
6 Screw Nut 4 CSN00302
6 M8螺母 M8 Screw Nut 4 CSN00304
7 弹性垫圈 Spring Washer 4 CSN00305
标准部件 Standard Parts
8 热油器 Crankca Heater 1 CSD00300
选择部件 Option Parts
3. 使用条件范围 Operating Conditions
蒸发温度 Evaporating Temp. -15～13℃
排气温度 Discharge Temp. 120℃以下 120℃ Max.
绕组温度 Winding Temp. 120℃以下 120℃Max.
烟的牌子
压缩机上壳温度 Shell Temp. (冷凝温度＋5℃)～120℃以下 (Condensing Temp.＋5℃)～120℃ Max.
压缩机油温 Oli Temp (冷凝温度＋10℃)～120℃以下 (Condensing Temp.＋10℃)～120℃ Max.
吸气压力 Suction Pressure 0.2～1.1MPa (起动、除霜等短时间运转除外；Except the short period such as start, defrost)
排气压力
Discharge Pressure
1.0～3.8MPa
压力比 Pressure Ratio 2～7.(起动、除霜等短时间运转除外；Except the short period such as start, defrost)
启动时系统平衡压力
System Pressure At Starting 2.08MPa以下 2.08MPa Max
起动时的压力差
Pressure Difference At Starting 排气压力－吸气压力≤0.30MPa D.P.-S.P. less than 0.30MPa
启停周期
On/Off Period 周期为10分钟以上，停止时间必须3分钟以上
10 minutes min/cycle, OFF should be over 3 minutes
异常升压/降压
Abnormal Press. Ri/Drop 上升:3.8MPa以下 Ri:3.8MPa Max. 下降:0.3MPa以上 Drop:0.3MPa Min.
配管（铜管）应力 Copper Piping Stress 启动时:50MPa以下 Start:50MPa Max. 运转时:10MPa以下 Run:10MPa Max.
冷媒水分含量
Refrigerant Moisture Level 350mg以下 350mg Max.
系统固体杂质含量
Solid Impurities Level 100mg以下 100mg Max.
运转倾斜角度
Tilt In Operation 压缩机倾斜最大5°以内 5 deg. Max.
※ 其他注意事项 Remarks:
1.制冷系统 The refrigeration system
1）润滑油与冷媒的重量比（润滑油/冷媒）应在0.4以上；
The ratio of oil to the refrigerant (oil/refrigerant) should be higher than 0.4 in weight basis. 2）当系统中压缩机存在液态冷媒回流情况时，应采用储液罐等设计避免液态冷媒回流；
When the compressor in the system has the liquid refrigerant flooding back operation,the accumulator is required.
3）向压缩机充油或冷媒时，必须从排气侧进行；
Charge oil or refrigerant from the discharge pipe.
工程培训4）系系统必须设置油分离器。如不能够保证压缩机运行的最低油量在油面镜三分之一处（350ml）时，可以从压缩机排气侧补充适量牌号为FVC68D的冷冻机油；
Oil parator must be located.If compressor oil fall short of one-third of sight glass( 350ml),The FVC68D must be injected from the exhaust.
5）每台压缩机都需要独立设置电流、压力、温度等保护装置；
Some protected device should be mounted for any compressor,for instance current,pressure and temperature.
6）系统高压压力开关参考设定值为3.6±0.1MPa；
We advi tting pressure of the high pressure switch as follow: 3.6±0.1MPa,
7）设置排气单向阀可以起到能量调节与压缩机不带压差启动；
The exhaust check valve may adjust capacity,and startup at no pressure difference.
8）压缩机顶部安装温度传感器来进行排气温度保护。
The Temperature nsor must be located on top of the compressor to protect the discharge temperature.
9) 在焊接压缩机配管时，要特别注意避免焊料进入压缩机内部。
Attention that avoiding solder falls into the compressor when soldering the tubes.
10）吸气管上需安装过滤器（100目）。
A filter is required before the suction tube of the compressor.
11）并联系统中回油毛细管前必须安装过滤器。
历程的近义词A filter is required before capillary tube in Multiple refrigerant.
12）并联制冷系统维护 Maintenance of the multi-compressor system
如果出现压缩机损坏，并且能确认该压缩机机械部分异常磨损或存在电机烧损的情况时，必须更换整台并联型压缩机组。如果系统中有气液分离器和油分离器，竭力推荐将其更换，同时对空调系统进行彻底清洗。
If the compressor was broken, and can confirm that was caud by malfunction of motor or abnormal wear out of mechanic parts,all of compressors in this system should be changed.We also highly suggest that the accumulator and refrigerant oil parator should be changed, and make a full washing of the system before installing the new compressors.
2.压缩机在去除吸、排气接头盖后，请勿放置10分钟以上；
Installation shall be completed within 10 minutes after removing the caps of suction and discharge tube.
3.请勿压缩空气；
Do not compress air.
4.在真空状态下请勿通电；
Do not energize under vacuumed condition.
5.热泵系统必须在压缩机底部安装油加热器（40～80W,220V）；
Crankca heater is required if the refrigeration system is heat pump.
6.运转时，各相间的电压偏差应在额定电压的3％以内；
Voltage (run):Voltage deviation each pha shall be within 3% of the rated voltage.
7.请勿反向旋转；
Do not rever rotate.
8.压缩机的接地装置应永久与制冷器具的接地装置连接；
The compressor’s earth connection should be connected with that of refrigeration system permanently and firmly.
9.成箱压缩机包装件的叠放堆码极限为2箱，装卸过程中严禁翻滚。
Pile limits 2 pallet.Tumbling is forbidden during handling.
4. 附图 Attachment
A-1 压缩机外形图 Dimension of Compressor A-2 防震胶座装配图 Mounting Asmbly
A-3 压缩机性能曲线 Compressor Performance Curve
A-4 基本电气原理图 Basic Circuit Diagram
A-5 温度传感器及安装图Temperature Sensor Asmbly Diagram
A-6 压缩机运转范围 Running Range Of Compressor
A-7 过载保护器U/T，S/T曲线 Overload Protector U/T，S/T Curve
A-8 热油器安装图 Crankca Heater Asmbly
A-9 基本系统图 Basic Refrigeration System
