日本平假名
ATTENTION:
Carefully check the unit prior to installation to ensure there is no damage. Do not dispo of any packaging until you are satisfied with this product.
1. Your installation must comply with all
local plumbing building codes. Have a
qualified tradesman do or approve your plumbing installation.
2. Plea read and save this guide before
using this product. Store the guide in a
safe place so you will know where it is when you want to refer to it.
Parts List
A
B C
D
F
[A] Stainless steel sink ...................................1 pc
[B] Strainer asmbly .................................2 ts
战胜自我
[C] Faucet with sprayer asmbly ...........1 t
[D] Soap dispenr asmbly ....................1 t
[E] T opmount clips .......................................1 pkg
[F] Colander ......................................................1 pc Tools and Materials Required T ape measure
Carpenter’s square
Pencil
Saber-saw/Jig-saw
Electric drill with 0.375 in (10 mm) drill bit and 2 in (51 mm) hole saw
Pipe wrench
Phillips screwdriver
Plumber’s putty
Silicone alant
Hacksaw
T eflon tape
T ail pipe
Counter Cutout
REPLACEMENT SINK
If this sink is a replacement sink, ensure that the cutout in your counter top is 32.25 in. x 21.25 in. (81.9 cm x 54 cm) with rounded
corners, as shown in the diagram below.
NEW INSTALLATION
1. If this sink is being installed in a new counter top, place the sink upside down on the counter top. Centre the sink left to right on the cabinet, making sure that it will not interfere inside with the structure of the cabinet or the counter top. The unit should be placed so that it is parallel to the front of the counter top and clears the overhang of the counter top and the face of the cabinet.
2. Trace the outline of the sink.
3. Draw a new line 0.375 in. (9.5 mm) inside
the outline. This will be the cut line. The size of the cut line should be 32.25 in. x 21.25 in. (81.9 cm x 54 cm). The cut line is smaller than the size of the sink and must have rounded corners. Do not cut the opening with square corners.
4. Using a 2 inch (51 mm) hole saw,
carefully drill four corner holes inside the cut line. U a saber-saw or jig-saw to cut along the cut line. Place a support underneath the cutout portion of the counter top to prevent it from falling during cutting.
Note: The instructions are for cutting Formica countertops only. Contact
your countertop distributor for the best method of cutting other materials such as marble, hard synthetics, etc.
5. Inrt the sink (A) into the hole in
the counter top to test the fit. Make
adjustments to the hole, if necessary.6. Once the fit of the sink in the counter top is preci, place the sink on a blanket and proceed with the next step.
Strainer Installation
1. Apply a aling ring of plumber’s putty
to the underside of strainer flange.
Sealant
五年级下册英语电子书2. Inrt the strainer body (2) into the sink (A).
3. Asmble the rubber gasket (3), frictionchristmas card
washer (4) and locknut (5) onto the strainer body (2) from under the sink (A).
1 Basket
2 Strainer body
3 Rubber gasket
4 Friction washer
5 Locknut
6 Plastic flange
department7 Tail pipe
(not supplied)8 Connecting nut
1
scorpions
4. Hand tighten the locknut (5). Do not
over tighten the locknut as it may split or deform the strainer body.
valentine是什么意思
5. Asmble the plastic flange (6) and tail
pipe (not supplied) (7) together. Attach the connecting nut (8), through the tail pipe (7) and plastic flange (6), to the lower threaded part of strainer body (2). Lock the connecting nut by hand. Do not
over tighten.
8
Faucet and Sprayer Installation
1. I nstall the faucet (1) by inrting the
bottom of the faucet with the O-ring on to the deck (2). Hand tighten the retaining collar clockwi.
2. I nrt the sprayer housing support
(3) through the pre-drilled hole in the
corner of the sink (A). Screw the nut (4) onto the threads of the sprayer housing support (3) and hand tighten.
3
3. Run the sprayer ho (5) down through
the sprayer housing support (3) and up through the central faucet mounting
hole. Connect the sprayer ho (5) to
the deck (2) and tighten with a wrench.
DO NOT OVER-TIGHTEN.
4. I nstall the deck (2) on to the sink (A)
with hot to the left and cold to the
right. From under the sink (A), thread
the mounting nuts (6) onto the faucet
shanks (7). Tighten the mounting nuts.
Soap Dispenr Installation 1. Inrt the dispenr
asmbly (2)
and pump top (1)
through the
pre-drilled hole
interest可数吗on the top surface
of the sink (A).
2. From the bottom
of the sink, inrt
the bottom gasket
(3) and lock nut
长裙的英文
(4) through the
dispenr asmbly
(2). Hand tighten.
3. Screw the soap
rervoir (5) into
the dispenr
asmbly (2) to
complete the
installation.
4. T o fill the rervoir,
acquire名词lift the pump top
(1) straight up to
remove it from
dispenr asmbly
(2). Carefully pour
in liquid soap to fill
the rervoir, then
replace pump top.
1
2
A
4
5
CAUTION: This unit is designed for
Using any other soap or chemicals in this unit may damage the dispenr and void the warranty.
