UART protocol
Hardware：
Computer side Balance side
RXD 2 ----------- 2 TXD发送数据 Transmit(tx) Data 的简写形式
TXD 3 ---------- 3 RXD发送数据 Transmit(tx) Data 的简写形式
SG 5 --------- 5 SG 信号地
Plea keep other pins unconnected.
Software Protocal：
5.4.1 SARTORIUS
5.4.2 SHIMADZU with CMD
5.4.3 Direct to windows
5.4.4 METTLER with CMD
软件协议：
5.4.1 SARTORIUS
5.4.2带CMD的SHIMADZU
5.4.3直接进入窗口
5.4.4梅特勒与CMD
SARTORIUS Protocal：
Baud rate t by 5.1.x from 150bps to 19200bps;
Parity t by 5.2.x;
Data bits：(5.2.1) 7-bit ASCII or (5.2.2) 8-bit ASCII;
Synchronization:1 start bit;1 stop bit
SARTORIUS Protocal：
波特率由5.1.x设置为150bps至19200bps;
由5.2.x设置的奇偶校验;
数据位：（5.2.1）7位ASCII或（5.2.2）8位威玛罗伊斯ASCII;
同步：1个起始位; 1个停止位
Data output Format:
Data package:
When in mass display: Stable -0.0011g
数据输出格式：
数据包：
当在质量显示：稳定-0.0011g
数据包长度：16 BYTES
Data package length:16 BYTES |
No. | 1 | 2 | friendly的反义词3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 |
HEX | 2DH | 20H | 20H | 20H | 30H | 2EH | 30H | 30H | 31H | 31H | 20H | 67H | 20H | 20H | 0DH | 0AH |
ASCII | - | | | | pretty woman0 | . | 0 | 0 | 1 | 1 | | g | | | CR | LF |
| | | | | | | | | | | | | | | | |
Data package No 1: Positive: Space( + ); Negative: Minus ( - ); Zero( _ );
Data package No 2-10: Weight information in ASCII format
Data package No 11-14: Weight unit
数据包1号：正号：空格（+）; 负值：减号（ - ）; 零（_）;
数据包No 2-10：ASCII格式的重量信息
数据包11-14：重量单位
compromiSHIMADZU with CMD Protocal：
Baud rate t by 5.1.x from 150bps to 19200bps;
Parity t by 5.2.x;
1 stop bit; (5.2.2) 8 data bits or (5.2.1) 7 data bits;
When in mass display: Stable -0.0011g
带CMD的SHIMADZU Protocal：
波特率由5.1.x设置为150bps至19200bps;
由5.2.x设置的奇偶校验;
1个停止位; （5.2.2）8个数据位或（5.2.1）7个数据位;
当在质量显示：稳定-0.0011g
Data package length:14 BYTES |
No. | 1 | 2 | 签发空头支票的处罚3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 |
HEX | 53H | 2DH | 20H | 20H | 20H | 30H | 2EH | 30H | 30H | 31H | 31H | 67H | 20H | 0DH |
ASCII | S | - | | | | 0 | . | 0 | 0 | 1 | 1 | g | | C/R |
| | | | | | | | | | | | | | |
Data package No 1: Stable: S
Unstable: U
Data package No 2: Positive: Space ( _ )
Negative: Minus ( - )
Data package No 3-11: Weight information in ASCII format
Data package No 12-13: Weight unit
Data package No 14: C/R
数据包1：稳定：S
不稳定：U
数据包2号：正号：空格（_）
负数：减号（ - ）
数据包No 3-11：ASCII格式的重量信息
数据包No 12-13：重量单位
数据包14：C / R
cpa是什么意思Caution Inputting characters and command codes not shown here into the balance may not only alter the pervious ttings but may also impair proper measurement. If by mistake characters or commands not shown here are entered into the balance, immediately unplug the power supply cable and wait about ten conds before plugging it in again 警告 将未在此处显示的字符和命令代码输入天平可能不仅会改变先前的设置，而且可能会影响正确的测量。 如果错误地将此处未显示的字符或命令输入天平，请立即拔下电源线并等待约10秒钟再插入下车英文 |
|
Command code | Function | Description |
D07 | 1 time output with stability information | 英孚怎么样The status of the stability mark is append to the head of the data with output. 稳定性标记的状态附加到带有输出的数据的头部。 |
T | youxingTaring | Corresponds to the Tare key |
| favicon | | |
METTLER with CMD Protocal：
Baud rate t by 5.1.x from 150bps to 19200bps;
Parity t by 5.2.x;
1 stop bit; (5.2.2) 8 data bits or (5.2.1) 7 data bits;
