压铸英语
A 安装尺寸 install dimension
凹模固定板 retainer plate
凹模 female die, female mold, negative mold
B 备 件 spare parts
变 质 modification
变 质剂 modification agent
扒 渣 slagging-off
保温炉 holding furnace
保压压力 dwell pressure
表面缺陷 surface defect
C 淬火硬度quenching hardness
抽 芯core
侧面抽芯side core
抽芯油缸core oil cylinder
插拔式结构plug
抽芯机构core puller
抽芯油缸支架bracket of cylinder
粗糙度roughness/degree
铸件表面粗糙度surface roughness
擦 伤galling
尺寸公差dimension tolerance of casting
除 气degassing
吹气净化blow purifying
除气剂degassing flux
出 渣de-slagging
出渣口slag hole
沉 渣sludge
出炉口tap hole
菜花头Cauli-flowering
超声波检验ultrasonic test
重 熔re-melting
D 端 盖cover
动模垫块spacer parallel
锻 钢 forged steel
氮化处理nitriding treatment
断 裂fracture
塑性断裂plastic fracture
导 柱guide pillar
导 套guide sleeve
导向板guide plate
导向件guide part
动 型moving die/ejector die/movable mould
动模座板moving clamp plate/bottom clamping plate
定模座板fixed clamp plate/top plate
定型fixed die/cover die
定模套版bolster/fixed die
顶 杆ejector pin
顶出结构ejector mechanism
顶 出ejector
吊装孔lifting eye
吊 环lifting ring
镀钛处理titanium plating treatment
多肉缺陷metallic projection
电火花electric spark
打 磨grinding
F 分流锥 divider/blast cone
分型面 mold parting/parting face/mold joint
附 页 attachment/appendix
复位杆 ret bar(rod)
附件故障 accessory
覆盖剂 covering flux
废金属料scrap
浮 渣cinder
反射炉 reverberatory furnace
废 品 reject
飞 边joint flash
仿 真simulation
G 规 格 specification/standard
数值孔径 numerical aperture (N.A)
固定段 gment
坩 埚crucible
坩埚炉crucible furnace
感应电炉electric induction furnace
沟 槽 blind scab
硅Silicon
H 滑 块 sliding block
滑块部件 moving parts
滑块退让 return/move back
焊 补 welding-on
横浇道 runner
合 模 die locking
横流道 runner
回炉料foundry returns
合 型 mold asmbling/closing/die locking
合型力 die locking force
化学成分不合格chemical consistence analysis
J 浇口套 sprue bush
浇排道系统pouring system
浇不足 misrun
浇 注 pouring
浇注断裂interrupted pour
浇道比 gating ratio
浇 包 ladle
精 整dressing and finishing
精 度 accuracy
接 口 connector
击 伤 shot damage
金相组织 metallographic structure
金属残液heel
金相检验metallographic test
金属型涂料 die coating/coating for metal mold
加压速度 rate of pressure increasing
间 隙 clearance
精 炼refining
精炼剂refining flux
精密铸造 precision casting
静 置holding/stewing
渗 透 impregnation
集渣装置dirt traps
夹杂类缺陷inclusion defects
夹 渣entrapped slag/slag inclusion
夹 具 tool fixtures
K 壳 体 housing
开 炉 blowing in
孔洞缺陷cavity
库 存 inventory
L 冷 却 cooling
冷却水管 cooling water pipe
冷却耐压管 cooling pressure pipe
冷却水管用密封圈 O-ring/aling ring/gasket ring
冷室卧式压铸机 horizontal (cold chamber) die casting machine
冷却系统 cooling system
冷却水接口 cooling water connector
冷 裂 cold crack
冷 隔 cold lap
铝 Aluminum
裂 纹 crack
拉 伤 caught casting
拉杆孔 draw bar
螺 纹 screw/thread
螺纹结构 screw structure
螺纹公称直径(直径 diameter)
公称尺寸(名义尺寸) specified size/nominal dimension
漏 油 leakage of oil
棱边倒角 edge
炉 料 charge
炉 衬 furnace lining
炉气分析flue gas analysis
炉前分析on-the-spot sample analysis
流 痕 bloom/flow line
力学性能不合格 physical-mechanical characteristic abnormal
M 毛 坯 rough/blank
毛坯铸件 rough casting
毛 刺 veining/burr
模 芯 core
模 框 frame
模 槽 mold channel
模 套 cha/bolster/frame
模具钢 die steel
模具图纸 mold drawing
内浇口 in-gate
冒 口 rir/feeder head
冒 口浇注系统 feeder head gating system
镁 Magnesium
锰 Mangane
密闭耐压系统 tightness test
N 内浇道 in-gate
镍 Nickle
P 配油盘 pressure plate
排气块 exhaust block
排气槽 air vent
排气孔 vent/venting channel
排气塞 venting plug
配合套 圆形:fitting sleeve 方型: fitting ca
跑 铝 aluminum slop out of mold
喷射冶金 injecting metallurgy
喷丸清理 shot blasting cleaning
抛丸清理 wheel blasting cleaning
偏 析 gregation
破坏性实验 destructive test
Q 取件机 extractor
去除浇冒口 de-gating
清 铲 chipping
缺陷铸件 defecting casting
气 孔 blowhole/gas cavity/pinhole/porosity
气孔缩 blowhole shrinkage
去毛刺 de-burring
去除氧化皮 de-scaling
氢 Hydrogen
清 理 cleaning
R 热处理 heat treatment
热电偶测温孔 thermocouple well
热电偶 thermocouple (TC)/pyod
热 裂 hot heating
熔 炼 smelting
熔化率 melting rate
熔炼损耗 total melting loss
熔 池 bath
熔 剂 flux
熔 渣 slag
S 水 管 water pipe
三维造型 3 D
三坐标测量仪 coordinate 3
上模座板 upper clamping plate
缩 孔 shrinkage
缩 松 disperd shrinkage
疏 松 porosity(disperd shrinkage)
渗 漏 leakage
缩 陷 sink/sink in/depression
试 块 test block/test piece/coupon
