Physical Properties of Iron-Oxide Scales on Si-Containing Steels
at High Temperature
Mikako Takeda1,Takashi Onishi1,Shouhei Nakakubo1and Shinji Fujimoto2
1Materials Rearch Laboratory,Kobe Steel,Ltd.,Kobe651-2271,Japan
2Graduate School of Engineering,Osaka University,Suita565-0871,Japan
The mechanical properties of oxide scales at high-temperature were studied in order to improve the surface quality of commercial Si-containing high strength steels.Specific oxides of Fe2O3,Fe3O4,FeO and Fe2SiO4were synthesized by powder metallurgy.The Vickers hardness,thermal expansion coefficient and thermal conductivity were measured at high-temperatures.A ries of measurements confirmed that the physical properties of the synthesized oxides were different each other.From the Vickers hardness measurements,it was verified that the hardness of each synthesized oxide was identical with the naturally-formed iron oxide,as obrved in the cross-ction of oxide scales on steels. The influence of the Fe2SiO4formed on Si-containing steels on the scale adhesion at high temperature and the surface property is discusd on the basis of the physical properties of the oxides.[doi:10.2320/matertrans.M2009097]
(Received March18,2009;Accepted June4,2009;Published August25,2009)
Keywords:high-temperature oxidation,oxide hardness,oxide thermal expansion coefficient,oxide thermal conductivity,silicon-containing steel,FeO,Fe3O4,Fe2O3,Fe2SiO4,adhesion,surface property
1.Introduction
The iron oxide scales that form on billets and slabs of hot-rolled steels are usually detached using a hydraulic descaling process.However,residual primary scales or condary scales that form after the descaling process remain on the steel surface through subquent hot-and cold-working,then influence the surface quality of thefinal products by modifying its mechanical properties,such as deformation, fracture and spalling.The residual scales may induce non-uniform surface temperature,which affects thefinal scale structure and mechanical properties of the steel.Hence,it is of great importance to examine/understand the physical and mechanical properties of iron oxide scales in order to control their formation and properties,and ultimately to improve the quality of steels.
The oxide scales that form on steels include Fe2O3,Fe3O4, FeO,which form in lamellar strata from the substrate towards the outer layer.In the ca of Si-containing steels,which are widely ud for au
tomobile bodies and frames in the form of high-tensile steel sheets,the inner-most layer,mainly compod of fayalite(Fe2SiO4)and FeO,can form at the interface between scale and steel.1–4)Therefore,the high-temperature physical properties such as hardness,thermal expansion coefficient,thermal conductivity,etc.of each oxide species need to be clarified in order to understand the deformation and fracture behaviour of scale and its influence on the surface properties after rolling.
The high-temperature deformation and fracture behaviour of the oxide species are not yet well summarid in the literature.Amano et al.5)reported the Vickers hardness of Fe2O3,Fe3O4,FeO and Fe2SiO4at RT(room temperature) and at1000 C,as measured by employing micro-indenta-tion.6)In this study,5)Vickers hardness were measured for the lamellar constituent oxides in cross-ctions of Si-containing steels.In terms of the deformation behaviour of oxides,Hidaka ported on the deformation of Fe2O3, Fe3O4and FeO at600–1250 C by measuring stress-strain curves.7,8)In the studies,tensile-test specimens of pure iron were completely oxidized underfixed conditions and tensile tests atfixed strain rates were conducted to obtain the deformation and fracture behaviour.
Although knowledge of such high-temperature mechanical properties of oxide scales is beneficial,their mechanical properties have been less extensively studied becau high-purity speci
mens of specific iron oxides are required in order to measure the parameters with sufficient accuracy.
This paper focus on the hardness,thermal expansion coefficients and thermal conductivities at high-temperatures of Fe2O3,Fe3O4,FeO and Fe2SiO4which were prepared by powder metallurgy and oxidation under a controlled atmo-sphere.Furthermore,the influence of the Fe2SiO4formed on the Si-containing steel on the scale adhesion at high-temperature,and surface property were investigated.
2.Experimental
2.1Preparation of specific oxide specimens
In this study,pure high-density FeO,Fe3O4,Fe2O3and Fe2SiO4were prepared by powder metallurgy and oxidation under a controlled atmosphere.Sintered compacts of each oxide were ud as test specimens to measure the physical properties at high temperature.Each synthesized specific oxide of iron-oxide was prepared using the following process.
FeO forms on Fe under limited oxygen partial pressures, ranging from2:8Â10À13Pa(equilibrium oxy
初中定语从句讲解
gen pressure of Fe2SiO4/FeO at850 C)to2:6Â10À13Pa(equilibrium oxygen pressure of FeO/Fe3O4at850 C).FeO is the stable pha at temperatures of570 C and above,but is not stable below570 C.9)Therefore,FeO may decompo into Fe and Fe3O4at RT.FeO that is formed at high temperature can be ‘frozen-in’by quenching,but this type of material is not suitable for measuring the mechanical properties in the high-temperature pha becau numerous pores are prent in such FeO specimens.
Materials Transactions,Vol.50,No.9(2009)pp.2242to2246 #2009The Japan Institute of Metals
In order to prepare an FeO specimen,finely-powdered Fe and Fe3O4were mixed in the ratio8:10by weight,and were then formed into blocks,55mm square by8mm thick.The shaped blocks were compacted by cold isostatic pressing under a constant load of150MPa,and then sintered at 1100 C for3.6ks in an Ar atmosphere.The sintered blocks were presd in a graphite mould at900 C for3.6ks in vacuum,under a constant load of50MPa.Den sintered compacts of pure FeO werefinally obtained.
On the other hand,Fe3O4forms on Fe over a wide range of oxygen pressures from2:6Â10À13Pa(equilibrium oxy-gen pressure of FeO/Fe3O4at850 C)to4:1Â10À3Pa (equilibrium
oxygen pressure of Fe3O4/Fe2O3at850 C). Fe3O4is relatively stable,but can be oxidized to Fe2O3 under high partial pressures of oxygen,and is reduced to FeO under low oxygen partial pressures.In addition,Fe2O3 forms on Fe under limited partial pressures of oxygen above 4:1Â10À3Pa(equilibrium oxygen pressure of Fe3O4/Fe2O3 at850 C).Fe2O3is stable in high partial pressures of oxygen,but is unstable and can be reduced to Fe3O4under low partial pressures of ,in an inert atmosphere. The blocks offinely-powdered Fe3O4and Fe2O3were compacted by cold isostatic pressing under a constant load of300MPa,and then sintered at1100 C for3.6ks.The Fe3O4and Fe2O3were sintered in atmospheres of Ar and air,respectively.
Si-containing steels promote the formation of lamellar fayalite:Fe2SiO4forms between the FeO layer and the steel substrate.Fe2SiO4forms in a narrow range of oxygen pressures between2:7Â10À14Pa(equilibrium oxygen pressure for SiO2/Fe2SiO4at850 C)and2:8Â10À13Pa (equilibrium oxygen pressure for Fe2SiO4/FeO at850 C), and therefore it is difficult to obtain pure Fe2SiO4by the oxidation of Si-containing steels.Therefore,Fe2SiO4was prepared by the sintering of fayalite powder.
The natural fayalite minerals were powdered and classified into the appropriatefineness(below150mesh),then formed into blocks.The shaped blocks were compacted by
cold isostatic pressing under a constant load of150MPa,and were sintered at1130 C for3.6ks in vacuum.
2.2Quantitative analysis of purity and sintering density
of synthesized specific oxide specimens
The synthesized oxide specimens were identified and were quantitatively analyzed by X-ray diffraction.In the quanti-tative analysis of the synthesized oxides,the main peaks of the X-ray diffraction spectra werefitted to Gaussian curves, and the intensities of the main peaks were obtained.The relative concentrations of the synthesized specific oxide were calculated by substitution in the following equation for the peak intensity.
C n¼
A nÂY n
hip pocket
ÆðA iÂY iÞ
ð1Þ
where C n is the relative concentration of component n,A n is the relative nsitivity coefficient of component n,and Y n is the peak intensity of component n.
The synthesized oxide specimens were machined and their densities were obtained at room temperature by measuring the volume-to-weight ratio.2.3Measurements of physical properties
2.3.1Hardness
The synthesized oxides,Fe2O3,Fe3O4,FeO and Fe2SiO4, were machined into work-pieces with dimensions of 10Â20Â3mm3,and then polished with a ries of emery papers up to1500grit,buffed,finally degread in acetone. The hardness of the work pieces were measured by a high-temperature micro indenter(Nikon MQ type)at temperatures up to1000 C using square-bad diamond and sapphire pyramids.A load of50g was applied for30s,and3 impressions were recorded for each sample.
Oxide scales that were formed on iron and steel substrates were also prepared as reference standards,and the hardness of the scales were also measured similarly.10mmÂ20mmÂ2mm work-pieces of high-purity Fe(99.99%)and an Fe-3.0mass%-Si alloy were oxidized at1000 C for1.8ks in an O2atmosphere.Oxide scales of about600m m in thickness were formed under the oxidation co
ndition.The hardness of oxide scales were measured using the square-bad diamond and sapphire pyramids as indenters for the lamellar oxides in a cross ction.5)
well是什么意思2.3.2Thermal expansion coefficient
The synthesized oxides were formed into3:5mmÂ3:5mmÂ18mm blocks,and were degread in acetone. The thermal expansion coefficients of the work pieces were measured between room temperature and1000 C using a thermo-mechanical analyzer(Rigaku TMA8140type)at a heating rate of5 C/min.A fud quartz bar was ud as a reference in this measurement.The thermal expansion coefficients of the synthesized oxides were measured in the air for Fe2O3,in an Ar atmosphere for Fe3O4and FeO,and in a He atmosphere for Fe2SiO4.
2.3.3Thermal conductivity
The synthesized oxides were machined into work pieces with dimensions of 10mmÂ1:5mm,and were degread in acetone prior to measurements.The thermal conductivities were measured at up to1000 C using a larflash analyzer (ULVAC-RIKO TC-7000type).The specific heats were measured by differential scanning calorimetry in an Ar atmosphere.The thermal conductivities of the synthesized oxides were calculated using the thermal diffusion coeffi-cient,the specific heat and the
sintering density.
3.Results and Discussion
3.1Purity and sintering density of iron oxide specimens The synthesized oxides were identified from X-ray diffraction spectra.Typical X-ray diffraction patterns of the synthesid oxides are shown in Figs.1to
4.It was confirmed that the synthesid Fe2O3,Fe3O4and Fe2SiO4were compod of a pure single pha.Although,slight inclusions of residual -Fe and Fe3O4were indicated for the synthesized FeO as shown in Table1,FeO was the predominant compound becau the concentration of Fe3O4was below 2.0mass%.From the results,we could assume that the synthesized oxides were esntially compod of single oxide species.
The densities of the synthesized oxides of Fe2O3, Fe3O4,FeO and Fe2SiO4were4.69gÁcmÀ3,5.08gÁcmÀ3, 6.27gÁcmÀ3and4.08gÁcmÀ3,respectively.Considering that
Physical Properties of Iron-Oxide Scales on Si-containing Steels at High Temperature2243
the densities of Fe 2O 3,Fe 3O 4,FeO and Fe 2SiO 4noted in the literature are 5.27g Ácm À3,5.18g Ácm À3,5.70g Ácm À3and 4.34g Ácm À3respectively,the sintering density of our synthesized Fe 2O 3was slightly low and that of the synthesized FeO was slightly high compared with the values available in the literature.10)
3.2Hardness
The hardness of synthesized iron oxides at room-and high-temperatures are shown in Fig.5.The hardness of all of the oxides decrea with increasing temperature,with the magnitude of the decrea occurring approximately in the following order:Fe 2SiO 4,Fe 2O 3,Fe 3O 4and FeO.In particular,the hardness of Fe 2SiO 4and Fe 2O 3are remarkably high at room temperature,but are equivalent to the other oxides above 400 C.The hardness of FeO is lower than the other oxides in the range between room temperature and 1000 C.The hardness of Fe 2SiO 4can not be exactly measured at 1000 C becau the melting point of Fe 2SiO 4is 1170 C and the material begins to soften at 1000 C.
In order to confirm the validity of the results,they were compared with the hardness of oxide scales formed on steels.The hardness of the synthesized iron oxides and of cross-ctional oxide
scales on pure Fe and a Fe-3.0mass%Si alloy are listed in Table 2.Variation of hardness of the synthesized oxides is similar to that of scales formed on steels.Furthermore,the order of magnitude of the
hardness
Fig.1X-ray diffraction pattern of Fe 2O 3
specimen.
Fig.4X-ray diffraction pattern of Fe 2SiO 4
specimen.
Fig.2X-ray diffraction pattern of Fe 3O 4
specimen.
Fig.3X-ray diffraction pattern of FeO specimen.
Table 1Concentration of oxide pha in FeO specimen (vol%).
Fe 2O 3Fe 3O 4FeO -Fe 0
1.9
86.8
11.3
Fig.5Hardness of the synthesized iron oxides at high-temperature.
Table 2Comparison of Vickers hardness (GPa)of the respective iron oxide scales and the cross-ctional oxide scales on iron.
Temperature全脑速读记忆
Sample form
Sintered specimen
Scale formed on iron
FeO RT 1.67 3.501000
C 0.04360.05Fe 3O 4RT 1.64 4.001000 C 0.05050.08Fe 2O 3RT 3.27 6.701000 C 0.07340.53Fe 2SiO 4
RT 3.29 5.501000 C
—
0.63
2244M.Takeda,T.Onishi,S.Nakakubo and S.Fujimoto
sheldon语录
of the synthesized oxides is consistent with that formed on the steels.However,the hardness of Fe 2O 3formed on the steel is much larger than synthesized Fe 2O 3at 1000 C.It is considered that the hardness of Fe 2O 3formed on the steel could not be measured precily becau its thickness is a few or veral tens of m m .Therefore,it is concluded that the properties of synthesized iron oxides that had been fabricated with high purity and density corresponds to that of oxide scales formed on steels.
3.3Thermal expansion coefficient
As shown in Fig.6,the thermal expansion coefficients of all of the synthesid oxides increa with increasing temperature,with magnitudes approximately in the following ascending order:FeO,Fe 3O 4,Fe 2O 3and Fe 2SiO 4.In particular,FeO exhibits the highest thermal expansion coefficient in the temperature range below 400 C.The thermal expansion coefficient of FeO abruptly increas at 600
不值得英文
–700 C.This phenomenon may be caud by a stabiliza-tion of FeO,becau FeO is becomes stable above 570 C.3.4Thermal conductivity
The temperature dependence of the thermal conductivity of the synthesized iron oxides is shown in Fig.7.The thermal conductivity is reduced approximately in the following ascending order:FeO,Fe 2O 3,Fe 3O 4and Fe 2SiO 4.A prominent feature is that FeO has the highest conductivity and Fe 2SiO 4shows the lowest in the temperature range between room temperature and 1000 C.The following is also noteworthy.The thermal conductivity of Fe 2O 3is the highest at RT,but changes remarkably smaller at high-temperature,while Fe 2SiO 4exhibits extremely reduced thermal conduc-tivity compared with FeO.3.5
Influence of the physical properties of iron-oxide scales at high temperature on the surface properties of the Si-containing steel
It was shown in ction 3.1–3.4that the high-temperature physical properties,such as hardness,thermal expansion coefficient,and thermal conductivity,are significantly differ-ent for each oxide species.
The scale structure and oxidation behaviour on the Si-containing steel have been described in many
literatures.1–4)On the Si-containing steel,inner-most layer consisting of FeO–Fe 2SiO 4mixture is formed beneath the outer FeO layer.1–4)However,Fe 2SiO 4in the inner-most layer,the amount of which increas as the Si content increas,suppress the outward diffusion of Fe ions from steels and hence the inner diffusion of oxygen ions predominates in the oxide growth.11)Therefore,as the Si content increa,the composition of outer scale layer changes from FeO to Fe 3O 4and Fe 2O 3.11)The results show that the fayalite (Fe 2SiO 4)affects the structure of the outer and inner scale layers on Si-containing steel.
In the following ction,the influence of the fayalite (Fe 2SiO 4)formed on the high-Si steel on the scale adhesion at high temperature and surface properties are discusd on the basis of physical properties of iron-oxide scale.
3.5.1The scale adhesion at high temperature of the
Si-containing steel
The thermal stress generated by the difference in the thermal expansion coefficient between inner-most layer and steel caus a spalling and cracking of the scale during the hot-rolling process.As described above,the inner-most layer on the high-Si steel is mainly compod of Fe 2SiO 4.Therefor
e,the scale adhesion of high-Si steel is influenced by the difference in the thermal expansion coefficient between the Fe 2SiO 4and steel.
As shown in Fig.6,the thermal expansion coefficient of Fe 2SiO 4increas as the temperature increas.The thermal expansion coefficient of Fe 2SiO 4at 1000 C is nearly equal to that of Fe(14:6Â10À6/ C at 800 C).12)By contrast,the difference in the thermal expansion coefficient of FeO and Fe is large at 1000 C.It is also reported that the scale adhesion of Fe 2SiO 4on steel at high temperature is greater than that of FeO.11)Therefore,the Fe 2SiO 4might strongly adhere to the substrate steel and is not detached by the descaling
process.
Fig.6Thermal expansion coefficients of the synthesized iron oxides at
high-temperature.
Fig.7Thermal conductivities of the synthesized iron oxides at high-temperature.
Physical Properties of Iron-Oxide Scales on Si-containing Steels at High Temperature 2245
编制英文3.5.2Surface property of the Si-containing steel after
rolling
As described above,the Fe2SiO4strongly adheres to the substrate steel,resulting in the deterioration of the descal-ability.The remaining Fe2SiO4suppress the outward diffusion of Fe ions from the steel and hence the inner diffusion of oxygen ions predominates in the oxide growth.11) It is also shown in Fig.7that the thermal conductivity of Fe2SiO4is lower than that of other oxides.This result suggests that the remaining Fe2SiO4on the substrate steel brings about a reduction in the cooling rate and a rising of the surface temperature.As a result,the thick Fe2O3,which is a higher order oxide,is formed as the outer-most scale layer on the Fe2SiO4-coated substrate steel.Therefore,the fracture and deformation behaviour of Fe2O3may directly affect the surface properties of high-Si steel.柔和的意思
It is shown in Fig.5that the hardness of Fe2O3is greater than that of the other oxides at800 C.It is also reported that the ability to deform Fe2O3is lower than that of FeO.7,8)As a result,the outer-most scale surface,mainly compod of Fe2O3,is crushed becau of its hardness and stiffness at 800 C,corresponding to the hot-rolling temperature.Finely-ground Fe2O3is often obrved on high-Si steels,which frequently form red scales on their surfaces and degrade the surface property of the high-Si steel.
4.Conclusion
In the prent study,we measured the high temperature physical properties of various iron oxides,constituents of oxide scales on steels,in order to clarify the dynamic behavior of the oxide scales that occur on practical steels. We lected FeO,Fe3O4,Fe2O3and Fe2SiO4as typical oxide species that formed on Si-containing steels,and synthesized artificial specimens of each type of oxide.The specimens were compod of a single oxide species,and were ud to measure the hardness,the thermal expansion coefficient and the thermal conductivity over the temperature range between RT and1000 C.As a result,it was found that the physical properties of the synthesized iron oxides differed significantly from each other.The hardness of the synthe-sized iron oxides was identical with the naturally-formed corresponding iron oxide obrved in cross-ctional oxide scales
on practical steels.The experimental results from this study are confirmed as reflecting the physical properties of the oxide scales that form on practical steels. Moreover,we discusd the relationship between the physical properties of oxides at high temperature and surface property after rolling the Si-containing steel.It is possible that Fe2SiO4affects the high-temperature adhesion,surface temperature,and surface property of the Si-containing steel after rolling.
REFERENCES
1) C.W.Tuck:Corros.Sci.5(1965)631–643.
2)W.W.Smeltzer,L.A.Morris and R.C.Logani:Can.Metall.Quart.9
(1970)513–519.
3)R.C.Logani and W.W.Smeltzer:Oxid.Met.3(1971)15–32.
4)K.Yanagihara,S.Suzuki and S.Yamazaki:Oxid.Met.57(2002)
281–296.
5)T.Amano,M.Okazaki,Y.Takezawa,A.Shino,M.Takeda,T.Onishi,
初一英语辅导报答案
K.Seto,A.Ohkubo and T.Shishido:Mater.Sci.Forum522–523 (2006)469–476.
6)G.R.Anstis,P.Chantikul,B.R.Lawn and D.B.Marshall:J.Am.
Ceram.Soc.64(1981)533–538.
瑞思学科英语怎么样7)Y.Hidaka,T.Anraku and N.Otsuka:Mater.Sci.Forum369–372
(2001)555–562.
8)Y.Hidaka,T.Anraku and N.Otsuka:Oxid.Met.59(2003)97–113.
9)L.S.Darken and W.R.Gurry:Physical Chemistry of Metals,
(McGrow-Hill Book Company,New York,1953)p.351.
10)K.H.Hellwege ed.:Landolt Borstein numerical data tables,Group3,
12,(Springer-Verlag,Berlin,1980)p.8.
11)M.Takeda and T.Onishi:Mater.Sci.Forum522–523(2006)477–488.
12)Metals Data Book,4th Edition,(Maruzen)p.14.
2246M.Takeda,T.Onishi,S.Nakakubo and S.Fujimoto
