西门子840d报警信息

更新时间:2023-07-26 20:15:46 阅读: 评论:0

Contents
1000 System error %1
1001 System error %1
1002 System error %1
1003 Alarm pointer for this lf-clearing alarm %1 is zero
1004 Alarm reaction to NCK alarm incorrectly projected
1005 Operating system error %1 parameter %2 %3 %4
1010 Channel %1 system error %2 action %3
1011 Channel %1 %3 %4 system error %2
1012 Channel %1 system error %2
1013 Channel %1 system error %2
1014 Channel %1 system error %2
1015 Channel %1 axis %2 system error %3
1016 Channel %1 axis %2 system error %3
1017 Channel %1 axis %2 system error %3
1018 Floating point arithmetic error in channel %1 task %2 station %3 FPU state %4
1019 Floating point arithmetic error at address %3 in channel %1 task %2 FPU state %4
1030 System error in link module error code %1  error type %2
1031 Link module generated an unspecified error %1 NCU %2  %3 %4
设计英文1160 Asrtion failed in %1 : line %2
2000 Sign of life monitoring: PLC not alive
2001 PLC has not started up
2100 NCK battery warning threshold reached
2101 NCK battery alarm
2102 NCK battery alarm
2110 NCK temperature alarm
2120 NCK fan alarm
2130 5V/24V encoder or 15V D/A converter undervoltage
2140 The actual rvice switch position forces a SRAM to be cleared at the next Power On (general ret active)
2190 Hardware plug-in module for communication with the digitizer missing
2192 No NCU link module exists, MD %1 ret
3000 Emergency stop
3001 Internal emergency stop
4000 Channel %1 machine data %2 [%3] has gap in axis assignment
4001 Channel %1 axis %2 defined for more than one channel via machine  data %3
4002 Channel %1 machine data %2[%3] assigns an axis not defined in channel
4003 Axis %1 assignment of master channel in machine data %2 incorrect or missing
4010 Invalid identifier ud in machine data %1[%2]
4011 Channel %1 invalid identifier ud in machine data %2[%3]
意见英文
4012 Invalid identifier ud in machine data %1[%2]
4013 Invalid NCU link configuration by machine data %1 = %2 on NCU_1 = %3
4014 Axis %1 ud veral times in %2
4016 Axis %1 already ud by NCU %2
4017 Axis container %1, location %2 already ud by NCU %3
4018 Axis container %1, location %2 not ud by any channel
4019 Axis container %1 advance not allowed with current status of NCU %2
4020 Identifier %1 ud veral times in machine data %2
4021 Channel %1 identifier %2 ud veral times in machine data %3
4024 Invalid axis configuration due to missing axis container machine data
vici
4026 Machine data %1[%2], link axis NC%3_AX%4 not ud by any channel
4030 Channel %1 axis identifier missing in machine data %2[%3]
4032 Channel %1 wrong identifier for facing axis in %2
4040 Channel %1 axis identifier %2 not consistent with machine data %3
4050 NC code identifier %1 cannot be reconfigured to %2
4060 Standard machine data loaded
4062 Backup data loaded
4070 Normalizing machine data has been altered
4075 Machine data %1 (and maybe others) not altered - permission level %2 needed
4076 %1 Ma
chine data could not be altered with permission level %2
4077 New value %1 of MD %2 not t. Requested %3 bytes too much %4 memory.
4080 Incorrect configuration of indexing axis in machine data %1
4100 System cycle time corrected for digital drive
4101 Position control cycle for digital drive reduced to %1 ms
4110 IPO factor incread to %1 ms
4111 PLC cycle incread to %1 ms火锅用英语怎么说
4112 Servo cycle incread to %1 ms
4113 Sysclock cycle incread to %1 ms
4114 Error in DP cycle of SDB1000
4200 Channel %1 geometry axis %2 must not be declared a rotary axis
4210 Channel %1 spindle %2 declaration as rotary axis missing
hurt什么意思4215 Channel %1 spindle %2 declaration as modulo axis missing
4220 Channel %1 spindle %2 declared repeatedly
4225 Channel %1 axis %2 declaration as rotary axis missing
4230 Channel %1 data alteration from external not possible in current channel state
4240 Runtime overflow for IPO cycle or position controller cycle, IP %1
4270 Machine data %1 assigns not activated NCK input/output byte no. %2
4275 Machine data %1 and %2 both assign the same NCK output byte no. %3
4280 Assignment of NCK-input/output byte via MD %1[%2] does not match hardware configuration
4282 Hardware of external NCK output assigned repeatedly
4285 Error on terminal block %1, error code %2
4290 Sign-of-life monitoring: local P-bus not alive
4291 Failure of module in local P-bus slot %1, error codes %2 %3 %4
4300 Declaration in machine data %1 is not allowed for geometry axis / spindle %2
4310 Declaration in machine data %1 index 2% is not allowed
4340 Channel %1 Invalid transformation type in transformation no. %2
4345 Channel %1 Invalid configuration in chained transformation no. %2
4350 Channel %1 axis identifier %2 machine data %3 not consistent with machine data %4
4400 Machine data alteration will cau reorganisation of buffered memory (loss of data!)
4502 Channel %1 anachronism: %2(%3) -> %4
5000 Communication job not executed
6000 Memory reorganized using standard machine data
6010 Channel %1 data block %2 not or not completely created,  error code %3
6020 Machine data have been altered - now memory is reorganized
6030 Limit of ur memory has been adapted
6401 Channel %1 tool not changed. No empty location for tool %2 Duplo no. %3 on magazine %4
6402 Channel %1 tool not changed. Magazine no. %2 not available
6403 Channel %1 tool not changed. Magazine location %2 on magazine no. %3 not available
6404 Channel %1 tool not changed. Tool %2 not available or missing
6405 Channel %1 command %2 has invalid PLC acknowledge parameter %3  - identifier %4
6406 Channel %1 PLC acknowledge for command %2 is missing
6407 Channel %1 Tool %2 cannot be placed in the magazine %3 on location %4. Invalid definition of magazine!
6410 TO unit %1 tool %2 with duplo no. %3 has reached tool monitor warning limit
6411 Channel %1 tool %2 with duplo no. %3 has reached tool monitor warning limit
6412 TO unit %1 tool %2 with duplo no. %3
has reached tool monitor limit
6413 Channel %1 tool %2 with duplo no. %3 has reached tool monitor limit
6421 Channel %1 tool not moved. Empty location for tool %2 Duplo no. %3 on magazine %4 not available
6422 Channel %1 tool not moved. Magazine no. %2 not available
6423 Channel %1 tool not moved. Location %2 on magazine %3 not available
6424 Channel %1 tool not moved. Tool %2 not available or missing
6425 Channel %1 Tool %2 cannot be placed in the magazine %3 on location %4 Invalid definition of magazine.
6430 Workpiece counter: overflow in table of monitored cutting edges.
6431 Function not allowed. Tool management is not active.
6432 Function not allowed. No tool assigned to spindle.空头支票罚款
6500 NC memory is full
6510 Too many files in the NC memory
6520 Too many protocol files in the NC memory
6530 Too many files in directory
6540 Too many directories in the NC memory
6550 Too many subdirectories
6560 Data format not allowed
6570 NC memory is full
6600 NC card memory is full
6610 Too many files open on NC card
6620 NC card has incorrect format
walch6630 NC card hardware is defective
6640 NC card is not inrted
telephonenumber6650 Write protection of NC card is active
6660 'Flash File System' option is not t
6698 Unknown NC card (%1/%2). Cannot write
7000 Too many compile cycle alarms defined
7010 Range of MMC alarm numbers for compile cycles exceeded
7020 Compile cycle alarm number has not been defined
7100 VDI area of %1 input and %2 output bytes defined by compile cycles exceeds %3 bytes
8000 Channel %1 option 'ur interrupt programs' not t
8010 Option 'activation of more than %1 axes' not t
8020 Option 'activation of more than %1 channels' not t
8021 Option 'activation of more than %1 mode groups' not t
8022 Option 'Activation of more than %1 kB SRAM' not t
8030 Channel %1 block %2 option 'interpolation of more than 4 axes' not t
8032 Option 'activation of more than %1 link axes' not t
8034 Option 'activation of axis containers' not t
8040 Machine data  %1 ret, corresponding option is not t
8041 Axis %1: machine data %2 deleted, corresponding option not sufficient
8098 Invalid combination of options (%1)
8100 Channel %1 block %2: Function not possible
10200 [up to SW 3.x] channel %1 NC Start with active alarm not allowed
10202 [up to SW 3.x] channel %1 NC Start not possible
10203 Channel %1 NC Start without reference point
10204 [up to SW 3.x only] channel %1 general error
10205 [up to SW 3.x only] channel %1 internal error in %2
10206 [up to SW 3.x only] channel %1 general error in function generator
10207 Channel %1 error when lecting or delecting the digitize function
10208 Channel %1 Continue program with NC Start
10209 Channel %1 internal NC Stop after block arch
10220 [up to SW 3.x only] channel %1 active
10221 [up to SW 3.x only] channel %1 not stopped at end of block
10222 Channel %1 inter-channel communication not possible
10223 Channel%1 command%2 already a
ctive
10224 [up to SW 3.x only] channel %1: command denied
10225 Channel %1 command %2 refud
10226 [up to SW 3.x only] channel %1: ret aborted
10227 [up to SW 3.x only] channel %1: command aborted
10230 [up to SW 3.x only] mode group %2 channel %1 program interruption does not permit mode change
10231 [up to SW 3.x only] mode group %2 channel %1 program stop does not permit mode change
10232 [up to SW 3.x only] mode group %2 channel %1 does not permit mode change
10240 [up to SW 3.x only] mode group %2 channel %1 mode change not possible
10241 [up to SW 3.x only] mode group %2 mode change in active channel %1 not possible
10242 [up to SW 3.x only] mode group %2 mode change in channel %1 not possible at this time
10243 [up to SW 3.x only] channel %1: mode group %2 cannot change mode
10249 [up to SW 3.x only] mode group %2 channel %1: mode change command canceled
10250 [up to SW 3.x only] channel %1 reorganization of block processing not possible at this time
10251 [up to SW 3.x only] channel %1
10252 [up to SW 3.x only] channel %1 reorg quence canceled
10253 [up to SW 3.x only] channel %1 reorg quence canceled
10254 [up to SW 3.x only] channel %1 reorg quence canceled
10255 [up to SW 3.x only] channel %1 reorg quence canceled
10256 [up to SW 3.x only] channel %1 reorg quence canceled
10257 [up to SW 3.x only] channel %1 reorg quence canceled
10258 [up to SW 3.x only] mode group %2 channel %1: ID invalid or duplicated
10259 [up to SW 3.x only] channel %1
10260 [up to SW 3.x only] channel %1
10600 Channel %1 block %2 auxiliary function during thread cutting active
10601 Channel %1 block %2 zero velocity at block end point during thread cutting
怎么了解一个人
10602 Channel %1 block %2 velocity limitation during thread cutting
10610 Channel %1 axis %2 not stopped
10620 Channel %1 block %3 axis %2 at software limit switch %4
10621 Channel %1 axis %2 rests on software limit switch %3
10630 Channel %1 block %2 axis %3 at working area limit %4
10631 Channel %1 axis %2 rests at working area limit %3
10640 [up to SW 3.x only] channel %1 block %3 spindle %2 cannot stop during gear change
10650 Channel %1 axis %2 incorrect gantry machine data, error code %3
10651 Channel %1 illegal gantry configuration, error code %2
10652 Channel %1 axis %2 gantry warning threshold exceeded
10653 Channel %1 axis %2 gantry error threshold exceeded
10654 Channel %1 waiting for synchronization start of gantry group %2
10655 Channel %1 synchronization of gantry group %2 in progress
10656 Channel %1 axis %2 gantry alarm not yet ud
10700 Channel %1 block %2 NCK protection zone %3 violated during automatic or MDI mode
10701 Channel %1 block %2 channel-specific protection zone %3 violated during automatic or MDI mode
10702 Channel %1 NCK protection zone %2 violated during manual mode
10703 Channel %1 channel-specific protection zone %2 violated during manual mode
10704 Channel %1 block %2 protection zone is not guarantee
d
10706 Channel %1 NCK protection zone %2 reached with axis %3 during manual mode
10707 Channel %1 channel-specific protection zone %2 reached with axis %3 during manual mode
10710 Channel %1 block %2 conflict with centerless grinding
10720 Channel %1 block %3 axis %2 software limit switch %4
10730 Channel %1 block %3 axis %2 working area limitation %4
10740 Channel %1 block %2 too many empty blocks in WAB programming
10741 Channel %1 block %2 direction reversal with WAB infeed motion
10742 Channel %1 block %2 WAB distance invalid or not programmed
10743 Channel %1 block %2 WAB programmed veral times
10744 Channel %1 block %2 no valid WAB direction defined
10745 Channel %1 block %2 WAB end positioning not clear
10746 Channel %1 block %2 block arch stop for WAB
10747 Channel %1 block %2 retraction direction not defined for WAB
10750 Channel %1 block %2 tool radius compensation activated without tool no.
10751 Channel %1 block %2 danger of collision due to tool radius compensation
coo是什么意思10752 Channel %1 block %2 overflow of local block buffer with tool radius compensation
10753 Channel %1 block %2: activate tool radius compensation in linear block only
10754 Channel %1 block %2: deactivate tool radius compensation in linear block only
10755 Channel %1 block %2: do not activate tool radius compensation via KONT at the current starting point
10756 Channel %1 block %2: do not deactivate tool radius compensation via KONT at the programmed end point
10757 Channel %1 block %2: do not change the compensation plane while tool radius compensation is active
10758 Channel %1 block %2 curvature radius with variable compensation value too small
10759 Channel %1 block %2 path is parallel to tool orientation
10760 Channel %1 block %2 helical axis is not parallel to tool orientation
10761 Channel %1 block %2 tool radius compensation for ellip with more than one revolution not possible
10762 Channel %1 block %2 too many empty blocks between two traversing blocks with active tool radius compensation
10763 Channel %1 block %2 path component of the block in the compensation plane becomes zero
10764 Channel %1 block %2 discontinuous path with active tool radius compensation
10765 Channel %1 block %2: 3D tool radius compensation not possible
10766 Channel %1 illegal change of surface orientation between block %2 and block %3
10767 Channel %1 block %2 processing with tilt angle unequal 0 not possible
10768 Channel %1  block %2 illegal tool orientation with 3D-cutter compensation
10769 Channel %1 block %2 illegal surface normal vector with 3D-cutter compensation
10770 Channel %1 block %2 change of corner type due to change of orientation with active tool radius compensation
10771 Channel %1 block %2 overflow of local block buffer due to orientation smoothing
10772 Channel %1 block %2 illegal orientation change when activating or deactivating 3D face cutting
10773 Channel %1 illegal tool orientation in block %2 at inside c

本文发布于:2023-07-26 20:15:46,感谢您对本站的认可!

本文链接:https://www.wtabcd.cn/fanwen/fan/78/1118770.html

版权声明:本站内容均来自互联网,仅供演示用,请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系,我们将在24小时内删除。

上一篇:Mitsunobu反应
标签:罚款   空头支票
相关文章
留言与评论(共有 0 条评论)
   
验证码:
推荐文章
排行榜
Copyright ©2019-2022 Comsenz Inc.Powered by © 专利检索| 网站地图