文件名称 | L171系列显示器检验规范 |
文件编号 | 试行 |
管理部门 | 品保部 |
生效日期 | 2003.07.24 |
页 数 | 共 6 页 |
版 本 号 | B 版 |
拟 制 人 | |
审 核 人 | |
批 准 人 | |
NO. | 显 示 方 式 (display mode) | 行 频(kHz) (horizontal frequency) | 场 频(Hz) (Vertical frequency) | 行 同 步 极 性 (horizontal sync. polarity) | 场 同 步 极 性 Vertical sync. polarity) |
1 | 640×480(60Hz) | 31.469 | 59.941 | - | - |
2 | 720×400(70Hz) | 31.469 | 70.087 | - | + |
3 | 640×480(72Hz) | 37.861 | 72.810 | - | - |
4 | 640×480(75Hz) | 37.500 | 75.000 | - | - |
5 | 800×600(56Hz) | 35.156 | 56.250 | + | + |
6 | 800×600(60Hz) | 37.879 | 60.317 | + | + |
7 | 800×600(72Hz) | 48.077 | 72.188 | + | + |
8 | 800×600(75Hz) | 46.875 | 75.000 | 福州雅思培训+ | + joss paper |
9 | 1024×768(60Hz) | 48.363 | 60.004 | - | - |
10 | 1024×768(70Hz) | 56.476 | 70.069 | - | - |
11 | 1024×768(75Hz) | 60.023 | 75.029 | + | + |
12 | 1280×1024(60Hz) | 63.981 | 60.020 | + | + |
13 | 1280×1024(75Hz) | 79.976 | 75.025 | + | + |
NO. | 项目(item) | 测试条件 (test condition) | IPQC规格 (IPQC spec) | 成品OQC规格 (product OQC spec) | 备 注 (remark) | ||||||||||||
1 | 画面 位置(pattern position) | 1. 所有工厂预置方式(Any factory pret mode) 2. Recall状态 (recall state) 3. 量尺或MASK (ruler or MASK) | 1.H-H’ 1.0mm V-V’ 1.0mm 2.上下左右不能显示ＬＣＤ金属外框(can’t e mental at top bottom ,left and right) | １.H-H’ 1.5mm V-V’ 1.5mm ２.上下左右不能显示ＬＣＤ金属外框(can’t e mental at top bottom ,left and right) | |||||||||||||
2 | 倾斜(Tilt) | lucky star 1. 所有工厂预置方式(Any factory pret mode) 2. 方格画面 (pattern: crosshatch) 3. 量尺或MASK (ruler or MASK) | E-F 0.5mm | E-F 0.5mm | |||||||||||||
3 | 白平衡 (white balance) | 1280×1024/75Hz 1.全白画面( Pattern: full white) 2.调对比度使Y=3cd/m2Max (contrast:Y=3cd/m2Max) 3.彩色分析仪(color analyzer) | 9300k： x=0.2810.015 y=0.3110.015 且yx 6500k x=0.3130.015 y=0.3290.015 且yx | 9300k： x=0.2810.020 y=0.3110.020 且yx 6500k x=0.3130.020 y=0.3290.020 且yx | IPQC项产线目视测试 TQA仪器测试 | ||||||||||||
4 | 全白画面 亮度(brightness full white) | 1.全白画面 (pattern: full white) 2.彩色分析仪 (color analyzer) 3．亮度/对比度调到最大（brightness/contrast to be max） | Y =240～260cd/m2 | Y =240～260cd/m2 | IPQC项产线目视测试 TQA仪器测试 | ||||||||||||
5 | 亮度均匀度(B/U)(brightness uniformity(B/V)) | 1.1280×1024/75Hz 2.全白画面 (pattern: full white) 3.彩色分析仪 (color analyzer) | 70% B.C.D.E亮度 / A亮度 144%(冷/热机皆需符合规格) (70% B.C.D.E (brightness / A brightness 125% (cold/warm state must be all suited for spec)) | 70% B.C.D.E亮度 / A亮度 144%(冷/热机皆需符合规格) (70% B.C.D.E (brightness / A brightness 125% (cold/warm state must be all suited for spec)) | IPQC项产线目视测试 TQA仪器测试 | ||||||||||||
6 | 白色均匀度 (W/U) (white uniformity(W/U)) | 1. 1280×1024/75Hz 2. 全白画面 (pattern: full white) 3. 工具:彩色分析仪 (color analyzer) | 眼观无明显差异，否则任意两点:X 12 Y 12 (not visible different ,any two spots: X 12 Y 12 | 眼观无明显差异，否则任意两点:X 14 Y 14 (not visible different ,any two spots: X 14 Y 14 | |||||||||||||
7 | 色温追踪 (color temperature tracking) | 1. 1280×1024/75Hz 2. 全白画面(AUTO后) 调对比度从最大至Y=10 cd/m2(full white (after auto)t contrast from Max. to Y=10 cd/m2 | x 0.013 y 0.013 | x 0.015 y 0.015 | IPQC项产线目视测试 TQA仪器测试 | ||||||||||||
8 | 色纯度 (purity) | 1.1280×1024/75Hz 2.全白、红、绿、蓝四色画面 (pattern: full white red green blue) | 所有画面不得出现异色或杂色 (can’t e any other color ) | 所有画面不得出现异色或杂色 (can’t e any other color ) | 冷/热机皆须符合规格 (cold/warm state must be all suited for spec) | ||||||||||||
9 | 色相(color pha) | 1.1280×1024/75Hz 2.彩条画面(color stripe pattern ) | 彩色分清，不能出现渗色及缺色(color is clarity and the pattern can’t e any other color) | 彩色分清，不能出现渗色及缺色(color is clarity and the pattern can’t e any other color) | |||||||||||||
10 | OSD/按键功能检测(OSD knob function confirm) | 1.所有的工厂预置方式(all the factory pret mode) 2.全白画面和方格画面(pattern: full white cross hatch) | 1.各功能键作用正常(the function knob is normal ) 2.控制范围符合规定要求(range changing is suited for spec) | 1.各功能键作用正常(the function knob is normal ) 2.控制范围符合规定要求(range changing is suited for spec) | |||||||||||||
11 | 水平垂直位置控制(the control of horizontal and vertical position) | 1.所有方式(any mode) 2.方格画面(pattern: crosshatch) | 能够调至满屏(adjustable to full screen) recall 画面不能 0ver scan | 能够调至满屏(adjustable to full screen) recall画面不能over scan | |||||||||||||
12 | 干扰/抖动(video noi/jitter) | 1.所有方式、所有画面(any mode,any pattern) 2.距离50CM检验(viewing distance) | 不得有干扰抖动、闪动(can’t e video noi jitter flicker) | 不得有干扰抖动、闪动(can’t e video noi jitter flicker) | |||||||||||||
13 | 聚焦(focus) | 1.1280×1024/75Hz黑底/反白“H”字画面(1280×1024/75Hz black raster/rever white. Crosshatch with “E”) 2.工厂预置方式(factory pret mode) | 1.“H”字清晰可见且相邻分开(“H” is clarity and parately) 2.四周与中心必须平均且能分(round and center must be are rage and parately) | 1.“H”字清晰可见且相邻分开(“H” is clarity and parately) 2.四周与中心必须平均且能分(round and center must be are rage and parately) | |||||||||||||
14 | 冷开机检查及方式切换(cold start test and mode change) | 1.冷机开机(cold start) 2.由低频至高频、高频至低频方式切换(change the frequency from low frequency to high frequency and high frequency to low. Frequency 3.任意方式至省电、省电至任意方式(any mode to power save power save to any mode) | 开机画面8秒内出现且无异常,10秒内稳定；方式切换时间 2秒且无异常；任意方式至省电时间 7秒、省电至任意方式时间 3秒(the display should appear within 8 conds and normal within 10 conds)time of mode change 2 conds and normal. time of any mode to power save 7sceonds.time of power save to any mode3conds | 开机画面8秒内出现且无异常,10秒内稳定；方式切换时间 2秒且无异常；任意方式至省电时间 7秒、省电至任意方式时间 3秒(the display should appear within 8 conds and normal within 10 conds) time of mode change 2 conds and normal. time of any mode to power save 7sceonds.time of power save to any mode3conds | |||||||||||||
15 | 高/低 压及ON/OFF测试 high/low Voltage and on/off test | 1.高低频三种方式 （high low frequency three mode） 2.电压为90264VAC （Voltage: 90 — 264VAC ） | ON/OFF 3 次，画面正常启动且无异常 (on/off 3 times the display is normal) | ON/OFF 3 次，画面正常启动且无异常 (on/off 3 times the display is normal) | 220/240 VAC以264Vac测试(220/240VAC test in VAC) 110/120 VAC以90Vac测试(11/120Vac test in 90Vac) IPQC项由TQA测试 | ||||||||||||
16 | DDC 测试(DDC test ) | 1.PC机(PC) 2.DDC测试(DDC test) | 1. DDC功能是否有效 (If DDC function is normal) 2. EDID资料及序号、期是否正确 (if EDID information and NO. date is test) | 1.DDC功能是否有效(If DDC function is normal) 2.EDID资料及序号、日期是否正确（if EDIT information and NO. Date is test) | IPQC项由TQA仪器测试 | ||||||||||||
17 | 省电 测试(power save test) | 1.SUSPEND(No V) 2.STAND BY(No H) 3.OFF MODE(No H、V) 4.高低频ON(High low frequency on) 5.工具:功率计(equipment: power meter) | 1.8W,电源灯为橙色(8W, LED is orange) 2.8W,电源为橙色(8W, LED is orange) 3.8W,电源灯为橙色(8W, LED is orange) 4.45W,电源灯为绿色(45W, LED is green) | 1.8W,电源灯为橙色(8W, LED is orange) 2.8W,电源灯为橙色(8W, LED is orange ) 3.8W,电源灯为橙色(8W, LED is orange) 4.45W,电源灯为绿色(45W,LED is green) | IPQC项由TQA仪器测试 | ||||||||||||
18 | 漏电流测试(leakage current test | 1.漏电流测试仪(leakage current test meter) 2.264Vac 50Hz(264Vac 50Hz) | 时间: 1 min(time:1 min) 漏电流:<3.5mA(leakage current: (3.5mA) | ||||||||||||||
19 | 高压 测试 hi-pot test | 1.测试仪hi-pot test meter 2.1500Vac或2121Vdc 1500Vac or 2121Vdc | 时间： 1-3c time:1 c 漏电流:10mA leakage current<10mA | 时间： 1.5 min time:1.5 min 漏电流:10mA leakage current<10mA | |||||||||||||
20 | 热稳 定性 heat stability | 任意方式冷开机10分钟至2小时 (Any mode cold starts. 10 min to 2 hours.) | 生产测试过程中无干扰、变色等异常现象 (Current es video noi. Change color in testing.) | 无干扰、变色等异常现象 (Can't e video noi change color in testing.) | IPQC项由TQA测试 | ||||||||||||
21 | 对比度测试 contrast ratio test | 1.英语六级多少分才算过彩色分析仪 (color analyzer) 2．全白、底色画面 （full white \ black raster） 3. Ret后测试。 4. 全白画面Y值/底色画面Y值。(all white Y amount/black raster Y amount) | ≥qcc是什么400：1 | ≥400：1 | IPQC项产线目视测试 TQA仪器测试 | ||||||||||||
22 | 音频测试audio test | 主机、音频软件（pc\ sound software） | 无失真、声道不平衡、声小、无声及功能控制不良等(no distortion\ track imbalance\sound small\no sound\functional badness) | 无失真、声道不平衡、声小、无声及功能控制不良等(no distortion\track imbalance\sound small\no sound\functional badness) | |||||||||||||
23 | 用户自设方式 ur t mode | 1.所有方式，调各功能键到任意状态,然后切换到其它方式,再切回自设方式 Any mode. Set all the function knob to any state. Then change to other mode. And change to recall mode again. 2.调各功能键,到任意状态forward是什么意思,关机后再重新开机 Adjust all function knob to any state. shut off and start again | 画面显示自设方式 The display appears lf t mode. | 画面显示自设方式 The display appears lf t mode. | |||||||||||||
24 | 画面状态设置 display state t | 所有方式 any mode | 测试完,按自调键,使画面处于工厂预置状态 After testing push lf-t knob. the display appear factory pret mode | 测试完,按自调键,使画面处于工厂预置状态 After testing push lf-t knob. the display appear factory pret mode | |||||||||||||
25 | 接主机 测试 connect to PC test | 接主机用WINDOWS、DOS的各方式和画面模拟用户测试 Connect to PC testing by all the mode and pattern of windows DOS. | ok | ok | IPQC项由TQA仪器测试 | ||||||||||||
26 | 出货 状态 out put cargo | 1. 所有方式为工厂预置方式。 All the mode are in factory pret mode | 1.所有方式为工厂预置方式 All the mode are in factory pret mode | ||||||||||||||
本文发布于:2023-07-20 12:34:48，感谢您对本站的认可！
本文链接：https://www.wtabcd.cn/fanwen/fan/78/1106885.html
版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系，我们将在24小时内删除。
| 留言与评论（共有 0 条评论） |
