HP BladeSystem c7000 安装配置手册

更新时间:2023-07-16 17:59:28 阅读: 评论:0

HP BladeSystem c7000 Enclosure Quick Setup Instructions
Part Number 411762-007
February 2010 (Seventh Edition)
Verifying the pallet contents
* Not shown
Installing the enclosure
WARNING:  Becau the fully-populated enclosure can
weigh up to 217.7 kg (480 lb), remove all components
and the rear cage from the enclosure before removing
the enclosure from the pallet to reduce the risk of
personal injury when moving the enclosure.妮娜 杜波夫
CAUTION:  When removing the rear cage and
midplane asmbly, the connectors on the midplane
asmbly are susceptible to damage. U caution to
avoid damage to the pins and connectors.
CAUTION:  Be sure the hinges are completely open肖申克的救赎经典台词
voa newsbefore installing the rear cage into the enclosure.
stainless steelFailure to do so can cau damage to pins and
connectors.
1.The enclosure can be installed in a rack or rack-free
environment. Select the proper location bad on requirements
detailed in the HP BladeSystem c7000 Enclosure Setup and
Installation Guide.
2.Remove all components from the front and rear of the
enclosure, and then remove the rear cage.
3.
lzg(Optional) Install the enclosure into a rack. See the HP
BladeSystem c7000 Enclosure Rack Template. For rack-free installations, omit this step.
4.
Install the rear cage into the enclosure, clo the hinges, and
了不起的盖茨比英文简介
tighten the thumbscrews.
Enclosure bay identification
Before installing front or rear components into the enclosure, review enclosure bay numbering for each component.
dullesFull-height device bay numbering
Half-height device bay numbering
Power supply bay numbering
Fan bay numbering
Installing the front components
CAUTION:  To prevent improper cooling and thermal damage, do not operate the enclosure unless all bays are populated with a component or a blank.
颈部瑜伽CAUTION:  Do not mix HP 2250W, HP 2400W High Efficiency, HP BL7000 2400W Platinum, or -48vDC power supplies in one enclosure. Install only one type of power supply in a single enclosure.
If your HP BladeSystem c7000 Enclosure is equipped with a three-pha power configuration, you need six power supplies. To install a power supply: 1. To gain access to all power supply bays, slide the HP BladeSystem Insight Display to the right or left as needed. 2. Remove the power supply blank.
3.
Inrt the power supply into the enclosure, and then clo the
power supply bracket.
NOTE:  This document discuss installation of AC
power supplies only. For information on configuring DC power supplies or HP Carrier Grade Solution
s, e the documentation that came with your power supply.
4. Add any ordered options to each rver blade: o  Additional processor o  Additional memory o  Mezzanine option cards
cookies怎么读5.
(Optional) If you are installing a full-height device, remove the half-height device bay shelf. If you are installing a half-height
device, omit this step.
6. Remove the connector covers.
xch
7. Install the rver or storage blades.
8.
Install device bay blanks into any unud device bays. If the empty bays are configured for a full-height device, join
two device bay blanks to create a full-height blank.

本文发布于:2023-07-16 17:59:28,感谢您对本站的认可!

本文链接:https://www.wtabcd.cn/fanwen/fan/78/1100023.html

版权声明:本站内容均来自互联网,仅供演示用,请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系,我们将在24小时内删除。

标签:颈部   瑜伽
相关文章
留言与评论(共有 0 条评论)
   
验证码:
推荐文章
排行榜
Copyright ©2019-2022 Comsenz Inc.Powered by © 专利检索| 网站地图