Aviation Devices & Electronic Components, L.L.C.
1810 Mony Street Phone: 817-738-9161 Fort Worth, TX 76102 FAX: 817-738-9163 Installation & Maintenance Specification IS-AG-010
Av-DEC Aircraft Antenna Gasket Installation
NOTE: Read this specification completely before antenna installation.
1. SCOPE
This specification describes the method for antenna and aircraft surface preparation and antenna installation using the Av-DEC Hi-TAK Polyurethane Gasket™ries antenna gasket, HT3326-5Self-Leveling Green alant, and Hi-TAK Polyurethane StretchSeal™ tape. This method is to be ud only for antenna gasket installations between an antenna and aluminum aircraft skin or ground plane.
2. APPLICABLE DOCUMENTS
Engineering orders, aircraft maintenance manual, avionics installation manual, and/or ur maintenance manual as applicable.
gasstation
3. REQUIREMENTS
3.1 MATERIALS - Cleaning Solvent - Isopropyl alcohol or other approved cleaning solvent. 3.2 SURFACE PREPARATION - Surfaces that will come in contact with the antenna gasket
shall be free of paint, dust, oil, grea, fingerprints, and other contamination prior to antenna installation. Any primer or paint shall be removed to expo clean bare metal. As
小学二年级英语下册
a means of adding extra protection it is recommended to paint 3/16” under the footprint of
the antenna. The surface shall be wiped with a clean, solvent dampened cloth, followed immediately by wiping with a clean dry cloth. Residue of previously applied adhesives, alants, or fillet aling materials shall also be removed. An appropriate chemical conversion coating may be applied to the aircraft skin surface and allowed to dry per manufacturer’s instructions. Inspect surface areas for corrosion and take corrective action bad upon current maintenance manual requirements.
3.3 GASKET INSTALLATION - Av-DEC Hi-TAK Polyurethane Gaskets™are supplied with
protective relea film on both sides of the gasket. Leave relea film in place until ready to install gasket. Remove gasket from the protective packaging, taking care not to fold or bend it. Verify that f
astener holes and connector cutouts in the gasket will align with the antenna when positioned for installation. Trim the perimeter of the gasket flush with the antenna if needed. Remove relea film from the side of the gasket marked “antenna side” and position gasket over the antenna. Beginning at one side or corner of the antenna, place gasket into position, carefully aligning gasket fastener holes with antenna fastener holes. Relea film should remain on expod “aircraft side” of gasket until immediately prior to antenna installation.
Aviation Devices & Electronic Components, L.L.C.
1810 Mony Street Phone: 817-738-9161 Fort Worth, TX 76102 FAX: 817-738-9163 Figure 1 Typical Antenna Gasket Installation with HT3326-5 Self-Leveling Green
3.4 SEALING ANTENNA CONNECTOR BASE - A major source of antenna corrosion occurs
from moisture leakage into the ba of the antenna connector. Although the antenna can be mounted with only the aled antenna gasket installed, Av-DEC highly recommends the application of HT3326-5 Self-Leveling Green alant to the connector mounting area.
HT3326-5 alant will prevent moisture ingress through the connector ba.
Do not open HT3326-5 package until ready for u. Follow instructions for priming and mixing on the HT3326-5 cartridge. Dispo of cartridge if it has been removed from package for more than 24 hours.
Apply a layer of Av-DEC HT3326-5 Self-Leveling Green alant to the antenna-mounting surface of the antenna connector, as shown in Figure 1. Allow the alant to cure for thirty minutes before mounting the antenna on the aircraft.
Aviation Devices & Electronic Components, L.L.C.
1810 Mony Street Phone: 817-738-9161 Fort Worth, TX 76102 FAX: 817-738-9163 3.5 SEALING ANTENNA CONNECTOR - An additional source of corrosion occurs from
moisture leakage into the antenna connector. Although the antenna can be mounted with only the aled antenna gasket installed, Av-DEC highly recommends the application of Hi-TAK Polyurethane StretchSeal™ (EN110589 or AD89513) tape over the connector.
StretchSeal tape will prevent moisture ingress into the connector.
To apply the StretchSeal tape, remove the tape from the package and unroll a small length of tape. Wrap the StretchSeal Tape around the mated connector with a 50% overlap while stretching the tape 25% to 50% to ensure a tight wrap. A tight wrap is necessary to ensure
a proper al. Coverage shall be from the ba of the antenna to at least ½” beyond the
connector and onto the insulation jacket of the coaxial cable.
Note: Aircraft cutout hole must be at least ¼” greater in diameter than the connector outer diameter when using StretchSeal tape.
Apply cable ties immediately above and below the mated connector and the free end of tape.
3.6 ANTENNA INSTALLATION - Remove relea film from the “aircraft side” of the gasket.
虔诚什么意思
Pre-position at least two fasteners through the antenna and gasket. Align fasteners at correct locations on the aircraft surface. Tighten each fastener one to two turns to hold the antenna in place on the aircraft. Install remaining fasteners through the antenna and gasket. Tighten fasteners in accordance with approved maintenance manual procedures.pearlfisher
九年级英语复习计划
Wait at least 15 minutes and retighten the fasteners.
3.7 FILLET SEAL - Fillet aling is not required, or needed, with Av-DEC antenna gaskets.
However, a fillet al may be ud along with the gasket if required by maintenance or installation documentation.
poke
4. MAINTENANCE - Installation of the Av-DEC Hi-TAK Polyurethane Gaskets™, HT3326-5
Self-Leveling Green alant and Hi-TAK Polyurethane StretchSeal tape requires no
variable是什么意思additional maintenance tasks than tho already specified in the approved maintenance manual procedures.
Av-DEC recommends replacing the Hi-TAK Polyurethane Gasket™, HT3326-5 Self-Leveling Green alant and Hi-TAK Polyurethane StretchSeal tape each time the antenna isig是什么
removed from the aircraft.
5. GASKET REMOVAL - After removing antenna fasteners, u a phenolic or wooden tool as
a wedge between the antenna and aircraft surface to parate antenna from the aircraft.
After the antenna is removed, cut the cable ties from the connector wrap (if prent) and remove wrap. Disconnect aircraft coax cable(s) and peel antenna gasket from aircraft.elc
Remove Self-Leveling Green alant from the antenna. U isopropyl alcohol or other approved cleaning solvent to remove any remaining residue.
>networking
