POE配置说明

更新时间:2023-06-24 17:57:37 阅读: 评论:0

以下为交换机的POE设置
<H3C>system //进入配置模式
ca985>speedo[H3C]poe legacy enable  //启用poe兼容性功能
Legacy detection is enabled
[H3C]
[H3C]undo poe temperature-protection enable  //关闭poe温度保护功能
The temperature protection is disabled. 
[H3C]                                     
[H3C]int Ethernet 1/0/1  //进入某个接口
[H3C-Ethernet1/0/1]poe enable //启用此接口的POE功能
[H3C-Ethernet1/0/1]quit
[H3C]
[H3C]poe-profile gao  //设置POE团体功能
[H3C-poe-profile-gao]poe enable
[H3C-poe-profile-gao]poe priority critical
[H3C-poe-profile-gao]poe mode signal
[H3C-poe-profile-gao]quit
[H3C]
英文翻译在线[H3C]int Ethernet 1/0/1 //将POE团体功能应用到某个接口上
[H3C-Ethernet1/0/1]apply poe-profile gao
[H3C-Ethernet1/0/1]quit
[H3C]
[H3C]apply poe-profile gao interface Ethernet 1/0/5 to Ethernet 1/0/8  //将POE团体功能应用到某些接口上
This operation may take a few minutes, plea wait.
[H3C]
[H3C]dis poe interface e1/0/1  //查看某个接口的POE信息
Port power enabled          :enable //此接口的POE功能是否启用
Port power ON/OFF            :off //此接口的POE是否正在供电
Port power status            :detection is in process
Port power mode              :signal
Port PD class                :0
商店英语port power priority          :high
Port max power              :10000 mW //此接口能提供的POE最大功率
Port current power          :0 mW //此接口开启POE后的当前功率
Port peak power              :0 mW //此接口开启POE后的最高功率
Port average power          :0 mW //此接口开启POE后的平均功率
Port current                :0 mA
you are gonna cryPort voltage                :0 V
<H3C>save  //保存当前配置
The configuration will be written to the device.
Are you sure?[Y/N]y
Plea input the file name(*.cfg)(To leave the existing filename
unchanged press the enter key):
Now saving current configuration to the device.
Saving configuration.
Unit1 save configuration flash:/config.cfg successfully
%Apr  2 00:13:16:901 2000 H3C CFM/3/CFM_LOG:- 1 -Unit1 saved configuration successfully.
opium
catti考试时间<H3C>ret  saved-configuration  //将交换机恢复为出厂配置
婊子英文The saved configuration will be erad.
Are you sure?[Y/N]y
Configuration in flash memory is being cleared.
Plea wait ...
Unit1 ret saved-configuration successfully.
<H3C>
<H3C>reboot  //将交换机恢复为出厂配置,需要重启设备后才能生效
Start to check configuration with next startup configuration file,
This command will reboot the device. Current configuration may be lost in next startup if you continue.  Continue?
[Y/N] y
This will reboot device. Continue? [Y/N] ynissa
#Apr  2 00:14:44:172 2000 H3C COMMONSY/5/REBOOT:- 1 -
河西智美
Reboot device by command.

本文发布于:2023-06-24 17:57:37,感谢您对本站的认可!

本文链接:https://www.wtabcd.cn/fanwen/fan/78/1030432.html

版权声明:本站内容均来自互联网,仅供演示用,请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系,我们将在24小时内删除。

标签:接口   功能   配置   出厂   交换机
相关文章
留言与评论(共有 0 条评论)
   
验证码:
推荐文章
排行榜
Copyright ©2019-2022 Comsenz Inc.Powered by © 专利检索| 网站地图