Chattiring t1,t3≤5mS.Bounce t2≤3mS.Detent feeling has to remains Contact resistance 200ΩMax all items is shall be for 1.5H,After which measurements shall be made.all items is shall be all items is shall be Application time of soldering iron:within 3S solder shall cover75% minimum of the surface being immerd.
所有项应满足初期规格。be subjected to standard atmospheric conditions Specifications in clau 所有项应满足初期规格
小学英语教学计划温度40±2℃，湿度90～95%的恒温恒湿槽中放置96±4atmospheric conditions for 1.5H,After which 温度-40±3℃的恒温箱中放置96±4小时,then the encoder.shall be subjected to standard satisfied.
mechanical abnormality.
不得有绝缘体的破损、变形、Electrical characteristics 常温、常湿放置1.5小时后测试.
The encoder shall be stored at a temperature of -40±3℃for 96±4H in a thermostatic chamber.And 所有项应满足初期规格。Specifications in clau 小时后，在常温、常湿中放置1.5小时后测试. The 温度85±3℃的恒温箱中放置96±4小时,satisfied.
in a thermostatic chamber.And the encoder shall with relative humidity of 90% to95% for96±4H enco
权利的游戏第7季der shall be stored at temperature of40 ±2℃ Specifications in clau 85±3℃for 96±4H in a thermostatic chamber.And The encoder shall be stored at a temperature of satisfied.
then the encoder.shall be subjected to standard 常温、常湿放置1.5小时后测试.
atmospheric conditions for 1.5H,After which 温度300℃以下，时间3秒以内.
端子在260℃±5℃温度的焊锡槽内浸锡3秒±0.5秒.measurements shall be made. 预热：基板表面温度100℃以下，时间1分钟以内.
Printed wiring board:single-sided copper clad 焊接：温度260±5℃或以下，时间3秒以内.
Preheating:1.Surface temperature of board:100℃. heat
or less 2.Preheating time:within 1 minute.shall be satisfied No 接触无异常.
Soldering:Solder temperature:260±5℃ or less Bit temperature of soldering iron:300℃less than Immersion time:within 3S 手焊 Manual soldering. 7-6.焊锡性
浸渍面须有75%以上焊锡附着at 260℃for 3S±0.5S.
Solderability The terminals shall be immerd into solder bath A new uniform coating of EC11 REVERSE DIRECTION SERIES SPECIFICATION
600～1000cycles/H without electrical load,after with 在无负荷条件下轴以600～1000周/小时速度回转，端子间接触阻抗200Ω以下
know
■在力矩≤时30,000±200周 7-3.耐热性 7-2.耐湿性 Damp heat
measurements shall be made.
Resistance Cold
7-4.低温特性一日连续5000～8000次.
laminate board with thickness of 1.6mm.使用基板:t=1.6mm的单面覆铜板.
槽焊 Dip soldering.
7-5.焊锡耐热性 to Soldering Dry heat
7 耐久性能 Endurance Characteristics
Rotational天津新东方英语培训
life
CONDITIONS
ITEM
条件(5000 to 8000 continuous cycles for 24 hours.）你好吗英文
7-1.回转寿命项目振荡 t1,t3≤5mS.突跳 t2≤3mS.SPECIFICATIONS
15,000±200cycles per 规格
The shaft of encoder shall be rotated at a speed of measurements shall be made.
尚余有轻微定位感.
30,000±200cycles per □在力矩＞时15,000±200周.
≤100mΩ
thank you什么意思
100mΩor less
Push 1Kgf to the shaft of encoder in the axial
4-1.按压寿命 Push-life
修订 Revision
日期 Date 经 办 Designed
审 核 Check
批 准 Approved
初始发行2011-1-4
版本 VERSION：A0
≤10mS
10mS or less 在端子和安装板间施加AC300V电压1分钟
仁爱教育网>中华人民共和国国家质量监督检验检疫总局
A voltage of300V AC shall be applied for 1 minute 用DC 5V 1mA 电压测定.
which a voltage of 250V DC is applied between Rated voltage:DC 5V
Note：The following specification is only suitable for the one type with switch construction of RE11 encoder ries.
1.额定值 Rating
2-1.接触电阻 2.电气性能 Electrical Characteristics
条件规格
1-2.最大额定电流 (阻抗负载)
Measurement shall be made under the condition 在端子和安装板间施加电压 250V DC.
100MΩ 以上100MΩ Min SPECIFICATIONS
Maximum operating current (resistive load):10mA Max
ITEM
CONDITIONS
1-1.额定电压
推动开关部分Push Switch Portion
备注：以下规格适用于RE11编码器带开关系列.
项目不得有绝缘破坏
Without arcing or breakdown.
3 机械性能 M echanical Characteristics
between individual terminals and bushing and plank.
圣诞节快乐的英文怎么写
EC11 REVERSE DIRECTION SERIES SPECIFICATION
4 耐久性能 Endurance Characteristics
fore of switch Single pole and single throw （push ON）
单极单投(按压ON)
接点数
Switch circuit and ■0.5±0.3 mm □1.5±0.5 mm
3-2.开关动作力 Operation 500±200gf Push static load to the shaft in the axial direction
Travel of switch
Voltage test at DC 5V 1mA.
2-2.绝缘阻抗 Insulation number of pul individual terminals and bushing and plank.以1秒钟1往返(OFF-ON-OFF)按压动作.
Shaft shall be push at 1 cycles/s(OFF-ON-OFF) resistance Contact 2-3.振荡 Bouncing resistance 3-1.开关电路 2-4.耐电压 Dielectric strength 在轴端，沿轴向施加的按压力.
3-3.开关移动量的速度按压。
20,000±200cycles.（0.5 Travel）文号 File No
EC11带定位反向专用受控编号 Document No Specification in clau shall □15,000±200次.（1.5行程）
direction under non-load conditions,and with a speed 15,000±200cycles.（1.5 Travel）
在无负荷条件下沿轴向施以1Kgf以下的力，以600次/小时■20,000±200次.（0.5行程）
be satisfied.
of 600 times/hour.
接触电阻:≤200mΩ.其它应满足初期规格.Contact resistance:200mΩ or less.
辛辛那提市
